Search:

Type: Posts; User: Nissanman

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    1,870

    There are several diagrams in the Haynes Manual....

    There are several diagrams in the Haynes Manual.
    This one is for the evaporative emissions control system: -
    46561
    What exactly are you wanting?
  2. Probably, but you can fold up a replacement out...

    Probably, but you can fold up a replacement out of metal fly wire and it will last the life of the engine.
    It is a very efficient oil/vapor separator so don't be tempted to use anything that may...
  3. Replies
    1
    Views
    1,014

    1. Compressed air? 2. I doubt it.

    1. Compressed air?
    2. I doubt it.
  4. When you say you fried it, does it still read...

    When you say you fried it, does it still read resistance?
    It might have glowed red hot but may still be OK.
    You could fit one from a late model car and it will work fine.
  5. Replies
    3
    Views
    1,444

    Haynes Manual 206, Chapter 13, page 232, 234,...

    Haynes Manual 206, Chapter 13, page 232, 234, Section 14 EGR system.
    Thermal Vacuum Valve.
  6. Replies
    9
    Views
    3,892

    My initial guess is the brushes in the alternator...

    My initial guess is the brushes in the alternator are worn out.
    When worn down they have very little spring tension on them and, providing the Voltage Regulator is doing the right thing, the exciter...
  7. Replies
    4
    Views
    577

    Yes, I've never had any problems getting the soft...

    Yes, I've never had any problems getting the soft plugs or the pressure relief valve.
    The valves I have seen and used are a self contained device with a spring loaded ball captive in it.
    You just...
  8. Replies
    4
    Views
    577

    Removing the valve is a good idea, it allows the...

    Removing the valve is a good idea, it allows the tank solution to circulate thoroughly.
    However, you should also remove the soft plugs from the front and rear faces of the block for the main oil...
  9. There are a couple of options for you, if the...

    There are a couple of options for you, if the trans. is to remain in the car.
    If the fill plug is stuck, the trans can be re-filled through the gearstick hole.
    If the drain plug is stuck, I'd be...
  10. Replies
    2
    Views
    573

    Check the relevant fuse for the blower motor....

    Check the relevant fuse for the blower motor.
    Have you tried it on all speeds?
    There is a dropping resistor inside the housing that provides the various speed settings.
  11. Replies
    46
    Views
    6,271

    Yes, I can do some measuring for you. While I am...

    Yes, I can do some measuring for you.
    While I am not disputing what you suggest, bear in mind the guy who is producing these has spent a LOT of time perfecting the moulds and material.
    If you can...
  12. Replies
    46
    Views
    6,271

    How's these apples;)

    How's these apples;)
  13. Replies
    6
    Views
    666

    I tend to think that the coolant got there during...

    I tend to think that the coolant got there during your dismantling work:ermm:
    If you measured 175psi compression in #4 then I'd take that as a good sign.
    I would put it all back together with the...
  14. Replies
    15
    Views
    2,994

    The drive pinion is located on the RHS of the...

    The drive pinion is located on the RHS of the rear extension housing of the transmission.
    You should see the speedo cable screwed into it.

    You should be able to get to the rear of the speedo and...
  15. Replies
    15
    Views
    2,994

    Likely to be a broken drive cable. You will need...

    Likely to be a broken drive cable.
    You will need to disconnect the cable from the speedo and the transmission to verify that the inner cable is intact and in fact turning freely.
    Broken inner will...
  16. Replies
    4
    Views
    2,178

    Here is a check list I posted on an Oz site some...

    Here is a check list I posted on an Oz site some time ago re wipers: -
    1) Disconnect the wiper arm linkage from the rear of the motor, switch it on and check it has reasonable slow and fast speeds....
  17. Replies
    46
    Views
    6,271

    A guy here in Oz has reproduced these. I...

    A guy here in Oz has reproduced these.
    I actually own some but they are at my sons' house and I haven't seen them yet.
    The Vendor has spent a LOT of time and effort to produce a quality item....
  18. Thread: Relays

    by Nissanman
    Replies
    5
    Views
    951

    Here's a copy of the wiring info for an S30, LHD...

    Here's a copy of the wiring info for an S30, LHD too:cool:
    http://im1.shutterfly.com/media/47a1dd38b3127ccefcf257c6c80500000030O00AauGjFq2bt2IPbz4S/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/...
  19. Replies
    7
    Views
    728

    Methinks you need to remove the rear wheels and...

    Methinks you need to remove the rear wheels and drums and have good look at the condition of the shoes and drums.
    The shoes may be worn out or there may be grit inside the drums.
    We won't know...
  20. Replies
    9
    Views
    1,423

    Does this help? The top stopper has small bumps,...

    Does this help?
    The top stopper has small bumps, the bottom one looks to be a flat washer, no vulcanizing.
  21. Replies
    10
    Views
    3,367

    Here is a pic. that may help: -

    Here is a pic. that may help: -
  22. Replies
    2
    Views
    649

    I can't help you with the $$ but I can offer some...

    I can't help you with the $$ but I can offer some advice.
    I had all my Z suspension powder coated years ago but I took some precautions first.
    Tape over all the surfaces that are of critical...
  23. The use of lead as a filler is in this day and...

    The use of lead as a filler is in this day and age unnecessary and dangerous.
    Providing there is a strong metal to metal weld at the seam, the use of Hi Tech Body Filler is the desirable solution....
  24. Replies
    4
    Views
    2,931

    Leave the fuse out and connect a 12V globe across...

    Leave the fuse out and connect a 12V globe across the fuse terminals to show you if/when the short circuit occurs.
    Remove all the globes in the circuit in question.
    Check that they are the correct...
  25. Replies
    24
    Views
    4,731

    ...and also here....

    ...and also here.
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4