Search:

Type: Posts; User: AlexS13

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    498

    Jeff, I'm running SU's on my L28.

    Jeff, I'm running SU's on my L28.
  2. Replies
    10
    Views
    498

    I'am also running a Web Cams #91 re grind on my...

    I'am also running a Web Cams #91 re grind on my 10:1 L28. Very happy with it, pulls hard to 7k no problem.
  3. Replies
    6
    Views
    666

    For my particular setup I have noticed an...

    For my particular setup I have noticed an improvement by doing this. The engine under light load / part throttle driving is much more responsive.
  4. Replies
    6
    Views
    666

    I have capped off the vacuum port on the front...

    I have capped off the vacuum port on the front carb and run my vacuum advance to the balance tube.
  5. Replies
    93
    Views
    5,434

    Count me in aswell!

    Count me in aswell!
  6. I had one hell of a time getting my RT mount in...

    I had one hell of a time getting my RT mount in aswell, it was a very tight fit. One thing I would suggest doing as a safety precaution would be to measure the rotating torque of the pinion before...
  7. Looking forward to the pics of the conversion....

    Looking forward to the pics of the conversion. You will notice a big improvement going to the 3.90! If you like hwy driving I will definetly recommend a 5spd swap with that gear ratio.
  8. I too have been dealing with some pinging issues...

    I too have been dealing with some pinging issues with my engine. Its a F54 L28 with a P79 head shaved .080
    I cannot seem to run more than about 10 degrees (set at 1000rpm idle) without getting...
  9. It is normal to have some black soot build up on...

    It is normal to have some black soot build up on the exhaust runners but if it looks wet/greasy as you describe that might indicate leaky valve seals.
  10. Thread: camshafts ?

    by AlexS13
    Replies
    7
    Views
    595

    I'am running a Web Camshaft in my L28. Very happy...

    I'am running a Web Camshaft in my L28. Very happy with it!
  11. Replies
    5
    Views
    1,345

    Thank you very much for the info. I will...

    Thank you very much for the info. I will definetly take it to a shop to get this done.
  12. Replies
    5
    Views
    1,345

    Chas, thank you for that tip. I tried backing off...

    Chas, thank you for that tip. I tried backing off the nut and putting it to it's original position but when I do this the nut is almost loose at it's original position. It almost seems like the...
  13. Replies
    61
    Views
    3,847

    I had this exact same situation happen to me. I...

    I had this exact same situation happen to me. I cut the pin as you did so I can separate the spindle from the control arm and took it to a local garage to press it out. To my surprise even with using...
  14. Replies
    5
    Views
    1,345

    R200 problems after replacing pinion seal

    I recently swapped in a R200 into my 240z and to my surprise it was very smooth and quiet. I did notice the pinion seal leaking quite badly so I decided to replace it. I searched and read multiple...
  15. This is exactly what I did to get my correct lash...

    This is exactly what I did to get my correct lash pad size. I initially ordered a .160 pad and did my wipe test but it was off so I had some old feeler guages that I cut up and used as shims along...
  16. Replies
    10
    Views
    923

    I remember doing this when building my motor...

    I remember doing this when building my motor aswell. It is a very tight fit so you have to be patient and take your time. Also don't forget about the sealant this is very important! When the crank is...
  17. Thread: F54 and P90

    by AlexS13
    Replies
    34
    Views
    2,683

    As Diseazd said, you should regrind your stock...

    As Diseazd said, you should regrind your stock nissan cam. The durability of the oem nissan cam is much better than the new billet cams. I myself sent my cam to a company called Web Cams and had them...
  18. Replies
    37
    Views
    4,807

    I've got an update for you guys! I recieved my...

    I've got an update for you guys! I recieved my centerforce stage 1 clutch last week and proceeded to remove my transmission. I was happy to see that the rear main seal was completely dry and I had no...
  19. Replies
    71
    Views
    9,587

    Here's mine.

    Here's mine.
  20. Replies
    37
    Views
    4,807

    I did use the 240z collar. I literally took...

    I did use the 240z collar. I literally took everything off the L24/4spd tranny including the collar and clutch fork and swapped it over to the L28/5spd tranny. I have ordered a 240z centerforce 1...
  21. Replies
    37
    Views
    4,807

    Well, I played with the free play at the clutch...

    Well, I played with the free play at the clutch master and I also confirmed I had the proper amount of free play between the clutch fork and slave cylinder rod. I went for a drive and it was no...
  22. Replies
    37
    Views
    4,807

    Leon and Lazeum, thanks for the explanation. I...

    Leon and Lazeum, thanks for the explanation. I think it's safe to say my issue isn't weird since the slippage I'am seeing is occuring in higher gear under load where the clutch is most likely to...
  23. Replies
    37
    Views
    4,807

    I adjusted the free play a little tonight so I...

    I adjusted the free play a little tonight so I will see what that does next time I drive it. I'am just as stumped as you guys are believe me! I think the torque the clutch must hold taking off in 1st...
  24. Replies
    37
    Views
    4,807

    Thanks for the input guys, I was extra careful...

    Thanks for the input guys, I was extra careful when putting on the rear main seal and the rear crankshaft bearing making sure I sealed up the corner's like it said to do in the "How to Rebuild Your...
  25. Replies
    37
    Views
    4,807

    L28 is toasting my 240z clutch

    Well, I just finished installing my freshly built L28, P79 shaved 0.080, aftermarket cam, header, intake, running round top SU's. I also swapped over to a zx 5 speed and a 3.90 diff. My stock 240z...
Results 1 to 25 of 48
Page 1 of 2 1 2