Search:

Type: Posts; User: Jason240z

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    25
    Views
    3,310

    Its now getting some paint on ...

    Its now getting some paint on

    Etch/primer/stone chip/paint/lacquer etc etc. Loads of seam sealer, really hope I don't have to do all this again!
    ...
  2. Replies
    25
    Views
    3,310

    Dam and blast. Managed to find someone local...

    Dam and blast.

    Managed to find someone local who still works with sand!! She looks lovely now..

    http://i101.photobucket.com/albums/m61/jason61c/photo5-5_zpsdd137a30.jpg
    ...
  3. Replies
    25
    Views
    3,310

    I would think you'd be better off with a bung, ...

    I would think you'd be better off with a bung, so for the times you have it standing inside you could remove to allow it to breathe? Not sure how else you'd do it. Well actually in hindsight, ...
  4. Replies
    25
    Views
    3,310

    I'm going to put a drain hole in it with a rubber...

    I'm going to put a drain hole in it with a rubber plug/bung, also seal on the rear of the badge where water can get in to run down. It'll be full of dinitrol.

    Rust Prevention Waxes and Oils
  5. Replies
    25
    Views
    3,310

    Well time for an update :) Its had all the...

    Well time for an update :)

    Its had all the metal work done, Dogleg repairs, inner wing behind doglegs, a couple of bits on the floor, floor rails(were damaged due to jacking in the wrong...
  6. why are you lap welding? that's asking for...

    why are you lap welding? that's asking for trouble.
  7. Replies
    25
    Views
    3,310

    Thanks, it was the most honest I could get here...

    Thanks, it was the most honest I could get here at the time, before the strip down it looked very very solid however it seems if you look you will find it. It made sense to start with the best I...
  8. Replies
    25
    Views
    3,310

    Well a slight thread revival! I had some rails...

    Well a slight thread revival!

    I had some rails made up, cleaned the floors underneath. found a few more bits of rust.......
  9. Good move, also feel how much easier the subaru...

    Good move, also feel how much easier the subaru diff turns compared to your old diff, less drivetrain losses.

    I've got a 4.44 plated subaru r180 LSD to go in mine with the beta motorsports...
  10. Replies
    23
    Views
    972

    I've a set going spare if you're interested.

    I've a set going spare if you're interested.
  11. Alan Thanks again for the link and thanks to...

    Alan

    Thanks again for the link and thanks to your friends for sharing. Its interesting looking at that and a normal 240z to see how they're constructed. Lovely colour too.
  12. Replies
    19
    Views
    1,314

    Are they webber DGV carbs? The dizzy is worth...

    Are they webber DGV carbs? The dizzy is worth about $150 on its own. Doesn't sound like much as the accessories are worth more than the block.
  13. Replies
    37
    Views
    2,975

    ATI do a range of dampers?

    ATI do a range of dampers?
  14. Replies
    2
    Views
    641

    I've seen those, they're suppose to go over the...

    I've seen those, they're suppose to go over the standard rails and cover a bit up under the engine bay too.
  15. Replies
    2
    Views
    641

    Floor rails...

    well after a none starter with some others I've got some floor rails, went for 1.5mm over the standard 1.2, over length too.

    Best bit was paying 25 for the pair, If I had a few sets made it drops...
  16. Replies
    25
    Views
    3,310

    Hi I managed to source one over here, glad to...

    Hi

    I managed to source one over here, glad to see there's someone else sorting their car out properly!

    Yes, lots of sand, inside all the wiper motor area and every join/panel on the front...
  17. Replies
    25
    Views
    3,310

    I'm still going through the process of getting it...

    I'm still going through the process of getting it tidy...... may take a while! :)
  18. Replies
    25
    Views
    3,310

    Yep, very pleased with the body :) Hr369: It...

    Yep, very pleased with the body :)

    Hr369: It wasn't be who bought the radio off you, I take it you've posted one to the sunny UK? the floor is pushed up, in the area in front of the seat...
  19. Remember when you bolt them on your into a whole...

    Remember when you bolt them on your into a whole world of chassis set-up. You need to know what you're doing and what you want. All this is very costly if you don't have an...
  20. Thread: Milestones

    by Jason240z
    Replies
    3
    Views
    650

    Looks nice, shame about the sunroof.

    Looks nice, shame about the sunroof.
  21. Poll: If its a proper restoration surely its got to be...

    If its a proper restoration surely its got to be a colour that the car could have had in the year it was made?
  22. Replies
    25
    Views
    3,310

    Slow progress here, body strip is in progress, ...

    Slow progress here, body strip is in progress, its timing consuming though and sometimes I wonder why i'm doing it, however it'll be worth it to have a proper rust free shell.

    The car's now on...
  23. The cam is by a company in the UK, its a Piper...

    The cam is by a company in the UK, its a Piper bp285.

    http://i101.photobucket.com/albums/m61/jason61c/camspec.jpg
  24. Cams with long duration but smaller lift?

    Howdy all.

    I've a cam

    300/300 duration
    valve lift 0.453" inlet
    valve lift 0.451 exhaust

    Timing inlet open 43btdc closes 77abdc
    exhaust open 77 bbdc
  25. How much are OEM headlight cover chrome trims worth?

    Continuing on a theme on here, I've got the chance to buy a set of headlight bucket's that have the OEM chrome headlight trims installed, the covers are missing.

    How much would these be worth? ...
Results 1 to 25 of 49
Page 1 of 2 1 2