Search:

Type: Posts; User: Zforce

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. That looks like a auto trans dizzy (dual point),...

    That looks like a auto trans dizzy (dual point), you need one from a manual trans car.
  2. Replies
    7
    Views
    1,952

    Removing the timing cover is pretty straight...

    Removing the timing cover is pretty straight forward, what you want to do is try not to damage the head gasket that will be left after you get the cover off. If you are not careful it will be leak...
  3. Replies
    12
    Views
    933

    If you are talking about turning the engine by...

    If you are talking about turning the engine by the cam sprocket bolt yeah that's a bad idea, you want to keep the tight side of the timing chain tight at all times.
  4. Replies
    24
    Views
    1,507

    I beg to differ ha ha.

    I beg to differ ha ha.
  5. Ok so where's the garage full of brand new gen...

    Ok so where's the garage full of brand new gen one Z's ?
  6. Replies
    1
    Views
    667

    You want to retain some sort of balance tube so...

    You want to retain some sort of balance tube so just get a early one.
  7. Replies
    203
    Views
    15,410

    The colder the x-ray table is the more you need...

    The colder the x-ray table is the more you need to be on it.
  8. Mallory pumps can be problematic if you don't use...

    Mallory pumps can be problematic if you don't use the matching 400 micron filter, trash in fuel will jam them up do to the gear rotor design.
  9. Never tried it but lots of folks reccommend a...

    Never tried it but lots of folks reccommend a Mazda rx7 pump from a early 80's model carburated car.
  10. Replies
    2
    Views
    708

    Sounds like your alternator is not charging, get...

    Sounds like your alternator is not charging, get a volt meter and check the voltage at the battery, it should read about 14.5 volts with the engine running.
  11. Thread: RIP Dan Welden

    by Zforce
    Replies
    12
    Views
    2,007

    During the 1999 cart season I went to the first...

    During the 1999 cart season I went to the first race at the Chicago Motor Speedway and watched the race from the Players racing paddock, they asked me if I would be interested in coming to the last...
  12. Replies
    4
    Views
    633

    You can pre oil the engine through the dizzy hole...

    You can pre oil the engine through the dizzy hole with a long 3/8 flat wood drill bit. Take the bit and file down the edges making it dull, remove the oil pump drive spindle, replace pump, chuck the...
  13. Thread: blue smoke

    by Zforce
    Replies
    7
    Views
    380

    Yep sounds like dry rotted valve guide seals, who...

    Yep sounds like dry rotted valve guide seals, who built your motor ? And what oil are you using ? and don't say synthetic.
  14. Replies
    12
    Views
    2,373

    Have you checked the the last chance filters in...

    Have you checked the the last chance filters in the carbs ? Su's run best slightly rich, also the stock fuel filter is a restriction. Another thing to check for is kinks in the rubber portions of the...
  15. Replies
    17
    Views
    2,842

    Ok, if you are using the autometer then you need...

    Ok, if you are using the autometer then you need to get the proper sending unit for that gauge and try 10/40 weight and see what happens.
  16. Replies
    17
    Views
    2,842

    What wieght oil are you using ? And you said you...

    What wieght oil are you using ? And you said you are using an autometer electric oil pressure gauge are you using the stock sending unit or the autometer unit ? And I don't think changing your oil...
  17. How can you be sure the engine was overheating ?...

    How can you be sure the engine was overheating ? did the radiator boil over ? If you put engine degreaser on the motor that will certainly cause smoking but only for a few seconds till it burns off....
  18. Replies
    6
    Views
    2,961

    Yeah at about 11:00, if its point down your 180...

    Yeah at about 11:00, if its point down your 180 deg out.
  19. Replies
    6
    Views
    2,961

    Your standing on the drivers side looking down...

    Your standing on the drivers side looking down the hole.
  20. Replies
    6
    Views
    2,961

    You actually fit the spindle by trial and error...

    You actually fit the spindle by trial and error till you get the drive tang at the 11:25 position when looking down the dizzy hole with #one at tdc, the dots are for reference since the dizzy will...
  21. Replies
    30
    Views
    3,195

    You are saying you cant get to any of the bolts...

    You are saying you cant get to any of the bolts at all with the heat sheild in place ?
  22. Replies
    30
    Views
    3,195

    If you can remove all of the hold down washers...

    If you can remove all of the hold down washers and the bolts on top of the manifold you should be able to remove the intake manifold with heat shield still in place.
  23. Replies
    30
    Views
    3,195

    I just did this yesterday on my carburated Z....

    I just did this yesterday on my carburated Z. There are no snags to worry about, it's just time consuming, it took about four hours including picking my kids up from school. The gasket I got was the...
  24. Replies
    364
    Views
    41,914

    Sticky: Today I changed the intake/exhaust gasket, gasket...

    Today I changed the intake/exhaust gasket, gasket blew on the intake side of #6 cylinder. Also replaced the drive shaft yesterday. After I did the gasket I had to do a quick test drive and get some...
  25. No, whatever was working before will work with...

    No, whatever was working before will work with any trans. Transmissions are the same, location of the diff determines what drive shaft to use.
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4