Search:

Type: Posts; User: zKars

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    18
    Views
    6,540

    To give some validity to your assertion that...

    To give some validity to your assertion that you're not thread bashing, you should also mention that those are blemished items, discussed here just yesterday and that the good ones that Esprit is...
  2. This issue of bypassing the heater has come up...

    This issue of bypassing the heater has come up many times. The correct way is to BLOCK/PLUG the heater hose connections at the head and lower rad hose fitting at the front. Do NOT just join these...
  3. Replies
    12
    Views
    1,244

    This is the stuff I bought. 2 Rolls Factory...

    This is the stuff I bought.

    2 Rolls Factory Electrical Non Adheasive Wiring Harness Friction Tape M | eBay

    Decent price and good seller.

    The tape is made by Elliot tape.

    Michigan Tapes...
  4. Replies
    22
    Views
    962

    Just to clarify why it won't work, the AAR is an...

    Just to clarify why it won't work, the AAR is an air bypass to the throttle blade, which affects (increases) idle speed when the engine is cold, but ALL air going to the engine must pass throught the...
  5. Thread: Another clutch ?

    by zKars
    Replies
    6
    Views
    330

    All L24/L26/L28 flywheels bolt to the crank, but...

    All L24/L26/L28 flywheels bolt to the crank, but not all clutches bolt to all flywheels. 225mm clutches use 6 mount bolts, 240mm use 9 bolts, in a different pattern. Sorry, the clutch pack has to...
  6. Replies
    4
    Views
    925

    The simplest way to essentially defeat all this...

    The simplest way to essentially defeat all this is to rewire the distributor so that the "advance" point contact goes directly to the "-" side of the coil, and remove the "retard" wire from the...
  7. While these are excellent and well tested methods...

    While these are excellent and well tested methods to diagnose very common ignition problem areas, I would preceed these checks by a simple check (immediately after failure) to see if you have spark...
  8. Thread: Off to ontario!

    by zKars
    Replies
    93
    Views
    5,452

    The shop lightening will have an effect on the...

    The shop lightening will have an effect on the preceived color. Get it out in the sun before you start wondering about correct shades. Might have to wait until next spring for sun though....
  9. Replies
    9
    Views
    1,193

    To expand on Tlorber's comments about using an...

    To expand on Tlorber's comments about using an adhesive, which I think is about the only hope you have of making an invisible repair, there are some pretty agressive and strong bonding agents out...
  10. Replies
    11
    Views
    588

    Help. Weak... Have turkey poisoning... Apparently...

    Help. Weak... Have turkey poisoning... Apparently cranberry sauce and gravy are NOT antidotes... Please save me...
  11. Replies
    11
    Views
    1,115

    The only way anyone has the right to poke fun at...

    The only way anyone has the right to poke fun at someone elses mistakes, is if they have a degree from the university of doing silly things. As anyone who has worked with me knows, I have a PhD from...
  12. The best solution to the points setting issue is...

    The best solution to the points setting issue is get rid of the points. There are several reluctor based distributors available, from later ZX dizzys that bolt right in to Pertronix aftermarket and...
  13. Replies
    11
    Views
    1,115

    You're going to feel silly when you pull that...

    You're going to feel silly when you pull that rubber protector off the threads...

    The two threaded holes in the crossmember were used for an optional weight that was hung off the crossmember to...
  14. Replies
    18
    Views
    6,540

    Futo Fab is getting serious about Z products

    Just wanted to let everyone know that I spotted a post on 510Realm this morning (I'm an equal Datsun opportunity guy ;) ) from Dave Patton at Futofab regarding an announcement of more 510 body parts...
  15. Replies
    2
    Views
    808

    I'm not positive, but I'm willing to bet its a 4...

    I'm not positive, but I'm willing to bet its a 4 x 0.7 mm machine screw. Can't go look at the moment but can confirm tonight.

    The part number is 08310-40612 if that helps you find some at the...
  16. Replies
    22
    Views
    1,631

    My favorite part (always) is when they drive away...

    My favorite part (always) is when they drive away smiling from ear to ear, or maybe when I listen to the sweet exhaust note fading into the distance, with their foot in it 'cause they can't resist......
  17. Replies
    22
    Views
    1,816

    Sorry, didn't make my joke/point clear enough. ...

    Sorry, didn't make my joke/point clear enough. Those who want their car "just like it came from the factory" would not accept rebuilt Z therapy carbs if they had the choice of real, period correct,...
  18. Replies
    22
    Views
    1,816

    Better running, undoubtly. But they are not...

    Better running, undoubtly. But they are not "right".....
  19. Replies
    206
    Views
    20,449

    oh baby... any close up shots of its under belly?

    oh baby... any close up shots of its under belly?
  20. Pretty sure you mean "Chevette" springs. Pretty...

    Pretty sure you mean "Chevette" springs. Pretty much the same car, right? ;)
  21. Replies
    36
    Views
    3,017

    I'm Baaaaaack.. Something came in the...

    I'm Baaaaaack..


    Something came in the mail yesterday. It's a lovely 15x40mm u-joint. I believe we have a staked u-joint replacement option. Way to find a good one CanTechZ!

    74387

    I've...
  22. Replies
    7
    Views
    1,020

    I apologise for my careless use of grade...

    I apologise for my careless use of grade information. The head of the stock bolt has a "9" on it. I believe this is equivalent to ISO grade 10.9 as John mentions. Look for this designation on the...
  23. Replies
    7
    Views
    1,020

    30 mm is the length. 12x1.25 is correct. Grade 9....

    30 mm is the length. 12x1.25 is correct. Grade 9. They are special Nissan bolts with a shoulder that fits the steering knuckle tightly.
  24. Replies
    12
    Views
    537

    Incredible! The pictures do not do them...

    Incredible!

    The pictures do not do them justice. I can imagine the sparkle of the facets in the sunlight.

    Power them up and bask in their radiance for 15 min. Get that last bit of tanning in...
  25. Replies
    4
    Views
    1,198

    There is a spring washer and cotter pin in that...

    There is a spring washer and cotter pin in that connection. The end of the J hook should be a nice fit through the holes in the U shaped hole too to remove as much chance for motion. Also evaluate...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4