Search:

Type: Posts; User: Darrel

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    738

    it's a roll pin, you will need a very small punch...

    it's a roll pin, you will need a very small punch to drive it out.
  2. post pics

    post pics
  3. Replies
    8
    Views
    1,095

    When replacing the master, did you use the old...

    When replacing the master, did you use the old rod or the new one?
  4. Replies
    3
    Views
    247

    I'm going to have to check out your '72 sometime.

    I'm going to have to check out your '72 sometime.
  5. swap the positive post closer to engine, in stock...

    swap the positive post closer to engine, in stock form the positive post was under the fender.
  6. Replies
    58
    Views
    2,362

    thanks, only asking because one side is NLA. Both...

    thanks, only asking because one side is NLA. Both inner are the same on my '97 altima, was wondering why they couldn't be used the same way with z car inners as long as the outer tie rod went with...
  7. Replies
    58
    Views
    2,362

    What is the main difference between the left and...

    What is the main difference between the left and right inner tie rod? Measurements the same only the thread is different RH vs LH?

    Outer tie rods the same except for RH vs LH threads as well?
    ...
  8. Replies
    4
    Views
    367

    Yes, it is spot welded. I have a couple of...

    Yes, it is spot welded.

    I have a couple of friends with the same failure. Not sure if they have done anything to it yet.

    Another spot weld would be ideal. until then maybe some tek screws as a...
  9. Thread: Any floats yet?

    by Darrel
    Replies
    9
    Views
    1,234

    http://www.classiczcars.com/forums/su-carb-central...

    http://www.classiczcars.com/forums/su-carb-central/52268-good-news-floats-hitachis-have-been-sourced.html


    From Bruce's thread in May.
  10. Replies
    10
    Views
    700

    what is the real vin number stamped on the driver...

    what is the real vin number stamped on the driver side firewall?
  11. Have you tried the dealer?

    Have you tried the dealer?
  12. Thread: nozzles

    by Darrel
    Replies
    6
    Views
    1,180

    the nipple where the hose connects to is fine. It...

    the nipple where the hose connects to is fine. It was the long brass/bronze that pulled out of the plastic piece. Looking through the parts fische, it looks like there is an oring. It is more or less...
  13. About ready to install the gas tank. Straps...

    About ready to install the gas tank. Straps painted and "new" insulators for the straps.(undercoated ratchet strap material.)

    Now I have to deal with a broken bolt that hold on the balance tube...
  14. Thread: nozzles

    by Darrel
    Replies
    6
    Views
    1,180

    Got it all cleaned up and used my vise to seat...

    Got it all cleaned up and used my vise to seat the tube in the whatchamacallit. Made sure it was seated in as far as the other nozzle. Judging by the force used it is an interference fit and very...
  15. Thread: nozzles

    by Darrel
    Replies
    6
    Views
    1,180

    nozzles

    While working on a set of gummed up carbs, one of the tubes came out of the feed nozzle. Yes, really gummed up. Is it an interference fit or does it need some kind of adhesive or cement to keep the...
  16. Replies
    28
    Views
    842

    Get it ready for June 28th. ZCCC track day.

    Get it ready for June 28th. ZCCC track day.
  17. Replies
    22
    Views
    1,313

    Don't drain the trans fluid until you get the...

    Don't drain the trans fluid until you get the fill plug out first.
  18. too late, pics at 10.

    too late, pics at 10.
  19. Replies
    7
    Views
    539

    pre made bracket. The only thing that would make...

    pre made bracket. The only thing that would make it better would be tek screws(self drilling/self tapping).
  20. I have the gas tank painted and about ready to go...

    I have the gas tank painted and about ready to go back in. I just need to solder the copper U for the top vent. I picked up fuel hoses for the tank and engine bay. Next thing to do is rebuild the 4...
  21. Replies
    16
    Views
    1,541

    check the wiring at the head temp sensor, if it...

    check the wiring at the head temp sensor, if it has the head temp sensor. between 5 and 6 spark plug on the head.
  22. Replies
    10
    Views
    397

    my '82 turbo blocks would leak when cracked. Not...

    my '82 turbo blocks would leak when cracked. Not sure if it's a problem with non turbo. Make sure you don't over tighten the new ones when you replace them.
  23. Replies
    5
    Views
    456

    That sounds like what happened to me after i...

    That sounds like what happened to me after i rebuilt the rear wheel cylinders. So I had a dry rear system. I started on the LR. I barely got anything to flow. It would seem the master would slowly...
  24. expansion tank delete....

    expansion tank delete.
    http://www.classiczcars.com/forums/tech-pubs-howto/19034-treating-inside-outside-gas-tank-por15-products-removing-evaporation-tank.html
  25. Less hoses to deal with. and as long as the...

    Less hoses to deal with. and as long as the remaining hoses are routed right there is no reason for the expansion tank. It's mainly for emissions and vapor recovery. Some 240z didn't even have the...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4