Search:

Type: Posts; User: buysell

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Thread: 260Z roof top

    by buysell
    Replies
    0
    Views
    648

    260Z roof top

    Selling roof of early 260Z. Includes headliner, visors & chrome trim as shown. Has minimal surface rust inside hinge mounts and antenna hole. Top has some dent's, not visible in pictures.
    Delivery...
  2. Replies
    13
    Views
    1,253

    I think I have 4 steel wheels from an early 260z....

    I think I have 4 steel wheels from an early 260z. I'm not sure of the offsets, but I can check if you are interested.
    -Justin
  3. Just a question for you, is it possible you are...

    Just a question for you, is it possible you are missing part #13?
    (from Car Parts Manual)
    74229
  4. Replies
    39
    Views
    1,706

    Just something to try, push the clutch in while...

    Just something to try, push the clutch in while the engine is running in neutral and see if the noise changes. Maybe something with the TO bearing as mentioned or a transmission input shaft bearing....
  5. It's about 8.5c/lb

    It's about 8.5c/lb
  6. I have a SWAG with the pressure dropping after...

    I have a SWAG with the pressure dropping after time. If the tank isn't vented enough, causing a vacuum inside the tank, would that cause the pump to work harder and loose pressure?
    Just a thought...
  7. Replies
    12
    Views
    565

    Is the firing order correct?

    Is the firing order correct?
  8. Replies
    12
    Views
    565

    How is the ignition timing? Sounds like it's too...

    How is the ignition timing? Sounds like it's too advanced.
  9. Replies
    20
    Views
    947

    Very good BeermanPete, Also check for vacuum...

    Very good BeermanPete,
    Also check for vacuum leaks in the engine compartment. You tested the distributer for correct operation, make sure the vacuum hoses are in good working order.
    --Justin
  10. Replies
    20
    Views
    947

    Are the vacuum and mechanical advance mechanisms...

    Are the vacuum and mechanical advance mechanisms working properly?
  11. Replies
    19
    Views
    1,711

    Check out these! Train Horns & Train Horn Kits:...

    Check out these!
    Train Horns & Train Horn Kits: Loudest Horns Available
  12. Replies
    9
    Views
    748

    Sorry my bad, the first pic shows the plugs that...

    Sorry my bad, the first pic shows the plugs that are in the bottom of the intake manifold, directly under each carb, about the size of a dime, these look like small block freeze plugs. I also have a...
  13. Replies
    9
    Views
    748

    I have a theory, I also have a early 260, and I...

    I have a theory, I also have a early 260, and I had a rough idle, not as smooth as I would like. I have since taken everything apart and discovered why. Under the intake manifold there are a few...
  14. Replies
    6
    Views
    1,290

    My guess is that your old ones are still stuck in...

    My guess is that your old ones are still stuck in place. The strut piston would have a lot of thread exposed if they were missing.
    Just my guess.
  15. Thread: I screwed UP!

    by buysell
    Replies
    11
    Views
    1,082

    UPDATE: I received the urethane bushings, and...

    UPDATE: I received the urethane bushings, and they are way too small. They just fall in with a gap all the way around. So after that, I called Courtesy Nissan for a dealer part search, Nothing. So...
  16. Thread: I screwed UP!

    by buysell
    Replies
    11
    Views
    1,082

    Very Carefully! JK, The hack saw blade fit just...

    Very Carefully! JK, The hack saw blade fit just between the rubber and sleeve. Before completing the cut through the inner sleeve, I took a chisel and finished cutting out the bushing.

    My local...
  17. Thread: I screwed UP!

    by buysell
    Replies
    11
    Views
    1,082

    Yes they are the Transmission mount bushing. The...

    Yes they are the Transmission mount bushing. The Nissan documentation calls them engine crossmember mount. My car is an early 260.
    I would get the aftermarket parts, but they require the outer...
  18. Thread: I screwed UP!

    by buysell
    Replies
    11
    Views
    1,082

    I screwed UP!

    In my process of removing stuff in prep for powder coating, I have cut out the Engine crossmember bushings. Come to fine out these are NLA.:stupid: Does anyone know where I may find two of these...
  19. Replies
    8
    Views
    1,747

    Anyone have experience with this kit?

    Anyone have experience with this kit?
  20. Just one thing to check, make sure the wires to...

    Just one thing to check, make sure the wires to the coil and distributor are on the correct side. If I remember correctly the "+" on the coil should have 12volts when ignition. is on, and the other...
  21. Replies
    21
    Views
    916

    Does your 73 have the flat top carbs? If so, I...

    Does your 73 have the flat top carbs? If so, I think that they also had the electric pump in front of the gas tank. Mine in my 260 if bad and caused the mechanical pump to work a lot harder. I'd...
  22. Thread: Weird.

    by buysell
    Replies
    8
    Views
    652

    Was this from a Red Green episode? He usually...

    Was this from a Red Green episode? He usually used K-cars.

    http://www.youtube.com/watch?v=n8WnKkJI3sM&feature=related
  23. Replies
    1
    Views
    614

    Your float bowls should have enough gas in them...

    Your float bowls should have enough gas in them to start your Z. Sounds like something else is going on.
    Just my .02
  24. Replies
    12
    Views
    865

    Just a SWAG. Where is the static ignition timing...

    Just a SWAG. Where is the static ignition timing at? If it's too much either way it could cause the carb. flame.

    -Justin
  25. Replies
    6
    Views
    754

    They look like "tow" straps.

    They look like "tow" straps.
Results 1 to 25 of 45
Page 1 of 2 1 2