Search:

Type: Posts; User: 280~Master

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    441

    Looks like you got some heat issues on that...

    Looks like you got some heat issues on that yellow wire..
  2. Replies
    20
    Views
    692

    Just go internally regulated alternator. Jump 2...

    Just go internally regulated alternator. Jump 2 wires or buy the plug from MSA..
    http://www.atlanticz.ca/zclub/techtips/alternatorswap/index.html
  3. Replies
    1
    Views
    259

    280z Alt upgrade plug

    I have been saving 280Z plugs for the voltage regulator and have gathered quite a few over the years.
    Was wondering what the interest would be if I make a few of the a plug and play plugs for the...
  4. Replies
    0
    Views
    392

    She's at it again!!!

    The last year has been fun and interesting.
    Well after a nice autocross event in 2013 and two spun bearings she is up and running.
    Engine bay was stripped and painted, extra wiring and brackets...
  5. Rare NICE Rust FREE AZ 1978 Nissan 280ZX AC 4 spd

    This one is must for the right person. LOL
    RARE Nice Rust Free AZ 1978 Nissan 280ZX AC 4 SPD S30 Datsun Non Turbo Fairlady | eBay
  6. Replies
    1
    Views
    262

    Turbo Drive Spindle position?

    Does this look right or is it off?
    Does it need to be rotated one tooth CCW?
    70078
    70079
  7. Replies
    0
    Views
    315

    Turbo Vacuum Lines Routing

    So I am having a problem trying to understand exactly where the vacuum lines go on my new turbo conversion. Think any of you could lend a hand on how to route these darn lines...?70073
  8. Replies
    12
    Views
    1,009

    My boots came from MSA. A little long but works...

    My boots came from MSA. A little long but works great. Even came with some highly overpriced Zip-ties.. lol
  9. Replies
    17
    Views
    1,430

    I am wondering kind of the same thing.. Tomo I...

    I am wondering kind of the same thing.. Tomo
    I need to break out the heat gun and test the plastic.
    If it is acrylic then it will polish itself nice, shiny and scratch free with the heat if not it...
  10. Replies
    3
    Views
    733

    Seems kinda high in price. I have seen the engine...

    Seems kinda high in price. I have seen the engine go for as low as 1000 and tranny like 750..
  11. Replies
    4
    Views
    542

    I like the fact that there is an air plane in the...

    I like the fact that there is an air plane in the pics...
  12. Thread: Rear Seal

    by 280~Master
    Replies
    9
    Views
    740

    I suggest buy some Nissan silicon and not the...

    I suggest buy some Nissan silicon and not the permatex stuff.. I could see and feel the difference between the two.
  13. Right now the car has a 3:90 R200 in it. I have a...

    Right now the car has a 3:90 R200 in it. I have a 4 speed and a 81-83 ZX 5 Speed(Which is close ratio).
    I use the car for auto cross
    a little road racing at Roebling Road Raceway
  14. Which Transmition? 4 or 5 speed with 390 gears & turbo..

    How about some thoughts and opinions..

    I am upgrading my L28 to a turbo and trying to decide on the transmission.

    So for those that have tried both what cha like...
  15. Replies
    51
    Views
    2,684

    What letters are on your cams? Got any C cams?

    What letters are on your cams? Got any C cams?
  16. Replies
    41
    Views
    1,546

    Just a note on the headers.. You could try Summit...

    Just a note on the headers.. You could try Summit $20 cheaper and free shipping..
    Footnotes:
    2 - Slip-fit collector.
    3 - Hookups for smog and engine management sensors.
    6 - Comes with header...
  17. Replies
    0
    Views
    578

    Datsun Rear speakers

    Thought someone might want these..

    New Datsun Attachments & Speaker
  18. Replies
    1
    Views
    441

    Rebello Racing

    So I am in the middle of a turbo rebuild for the 76 and have to say it is been an adventure.. :stupid: I have hit a couple of bumps but that is to be expected.. I must say that Dave at Rebello Racing...
  19. Replies
    35
    Views
    2,167

    Burl, My cars have always ran dead center..Even...

    Burl,
    My cars have always ran dead center..Even in the west TX heat years ago. I have seen cars that run over the M and run just fine. Who knows whats wrong if anything is..
    My thoughts,
    Gauge is...
  20. Replies
    9
    Views
    1,260

    My positive battery cable is from a 92 Honda...

    My positive battery cable is from a 92 Honda accord LX. It has the same type of end clamp that TomoHawk pictured. Its also a perfect length. My Neg cable is of the same type off of an Isuzu of...
  21. Replies
    6
    Views
    1,030

    I use the site to find basic prices for Z parts....

    I use the site to find basic prices for Z parts. I also use them to look at the fiche they offer for my other Nissan vehicles..
  22. Replies
    12
    Views
    908

    While the engine is at the machine shop the...

    While the engine is at the machine shop the breather tube has been removed and I am having the block portion tapped with a 1" pipe thread. This will allow for AN fittings and Stainless hose to be...
  23. Replies
    12
    Views
    671

    For that price I would have to see it and drive...

    For that price I would have to see it and drive it. Its located in Canada so it must have been keep in a pretty nice garage all its life to stay that nice.
  24. Replies
    9
    Views
    722

    Why not make some type of a magnetic base for the...

    Why not make some type of a magnetic base for the mirror so it's removable. This is what I plan on doing when I get my set.
  25. Replies
    22
    Views
    2,323

    I used the Kia Sportage and have no problems at...

    I used the Kia Sportage and have no problems at all. Just adjusted the strikers and everything closes great. Seals like a champ and I would recommend that mod for any Z not trying to be original 100%.
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4