Search:

Type: Posts; User: 71Nissan240Z

Page 2 of 4 1 2 3 4

Search: Search took 0.01 seconds; generated 38785 minute(s) ago.

  1. If somehow that control arm swung back into the...

    If somehow that control arm swung back into the wheel well from doing anything spirited to your car u would be in a world of hurt and probably have an accident. If it was me i would re tap the hole...
  2. Replies
    12
    Views
    474

    The hot cold control blend switches need to be...

    The hot cold control blend switches need to be checked regarding the heater. Your ac...you have a low pressure switch. It might be bad. Also check ur expansion valve. It is whats used to meter the...
  3. Replies
    22
    Views
    1,319

    I wouldnt listen to anyone but you and your car....

    I wouldnt listen to anyone but you and your car. Set the timing in a reasonable range and run premium. U will never dial it in by ear tuning. You can only get it in a range. Dynos are good to see...
  4. Replies
    12
    Views
    474

    Thats way too much pressure. The compressor...

    Thats way too much pressure. The compressor cannot work well when u overcharge the system. You need to refer to the manual on the pump. Most cars take two to three small cans of stuff. Everytime i...
  5. This is why its a good idea to run a lot of your...

    This is why its a good idea to run a lot of your electronics through a relay system. My headlights and fog lights both get supplied power directly from the battery and use the light switch as a...
  6. Replies
    23
    Views
    1,756

    I would be too worried about rock chips and...

    I would be too worried about rock chips and cracks with those headlight lenses. IMO they aren't worth using on a drivers car. Maybe a garage queen that u never drive. Otherwise no.
  7. Replies
    15
    Views
    2,072

    I refreshed a set of these for a friends car...

    I refreshed a set of these for a friends car once. Took all the needles out and blew carb cleaner through all of them. Make sure u lable each needle and emulsion tube as theres two circuits in each...
  8. Replies
    4
    Views
    646

    What do u mean reinstall the drain plug. Its...

    What do u mean reinstall the drain plug. Its reverse of removal.
  9. Replies
    1
    Views
    466

    I need a hand throttle

    Like the title says. Im looking extensively for a hand throttle to complete my interior restoration. I emailed kats but there was no response. Anyonre have one or know where to find atleast the...
  10. Replies
    1
    Views
    620

    i scored at the junkyard today

    at a junkyard in sherwood oregon i came across a 1984 maxima with 300,000 miles. I saw it. Checked the plugs...no oil. Okay...new filter....wires....okay i went home and tried to find a n47 off a...
  11. Replies
    6
    Views
    887

    Cleaned the contacts reseated them and recessed...

    Cleaned the contacts reseated them and recessed the board a little further in to make up for the worn switch plus added a little grease. Alll is. Thanks guys
  12. Replies
    6
    Views
    887

    Hazard switch bad. Thanks for the wire diagram.

    Hazard switch bad. Thanks for the wire diagram.
  13. Hazard switch lost continuity on the turn signal...

    Hazard switch lost continuity on the turn signal and brake light side. clean the contacts and see if it works. Or rig a double pole relay two position switch if it dont work or get an O.E.??"
  14. Hazard switch lost continuity on the turn signal...

    Hazard switch lost continuity on the turn signal and brake light side. Gonna clean the contacts tomorrow and see if it works. Ill have to rig a double pole relay two position switch if it dont work...
  15. Replies
    6
    Views
    887

    mystery blinker problem

    i hope somene has a wire diagram for a 1971 zed.

    Basically i used the stock fog lamp wire harness to install lights. Everything went fine.

    My turn signals dont work.
    Tested the switch-good...
  16. Replies
    497
    Views
    94,989

    Thanks for all ghe pictures and information for...

    Thanks for all ghe pictures and information for our z cars kat!
  17. Replies
    214
    Views
    6,191

    Those series onez are hard to come by. Mines like...

    Those series onez are hard to come by. Mines like a series one and a half lol
  18. Replies
    63
    Views
    2,654

    Yeah. You should do a compression test. Leakdown...

    Yeah. You should do a compression test. Leakdown would actually be better. Because it will steer u to where and what cylinder is having problems sealing.
  19. Replies
    7
    Views
    586

    Peter mcdonald in your neck of the woods coild...

    Peter mcdonald in your neck of the woods coild probably help u
  20. Replies
    2
    Views
    691

    Why did it pop off to begin with? Make sure ur...

    Why did it pop off to begin with? Make sure ur valves are adjusted and not too loose. Allso make sure all the rock arm springs are installed.
  21. Replies
    14
    Views
    1,294

    Your alternator has a roll on voltage that...

    Your alternator has a roll on voltage that increases with rpm
  22. Replies
    3
    Views
    433

    halfshaft bolts? special tool?

    I took them off to change the ujoints and diff seal. Now for some reason i cannot get the bolts on the diff side. I cant get a swivel socket i can barely get a wrench in there which is what i used to...
  23. Replies
    91
    Views
    8,592

    Damn those knobs look great. Does anyone know...

    Damn those knobs look great. Does anyone know where I can get an original shifter with a dragon looking thing on the top? Ive seen one before on datsun classifieds. the dragon or animal is yellow.
  24. Replies
    17
    Views
    1,055

    man that sucks to have to destroy an orginal...

    man that sucks to have to destroy an orginal aluminum drum
  25. Replies
    70
    Views
    2,450

    Well I've seen a dyno on a friends car gain a few...

    Well I've seen a dyno on a friends car gain a few ponies and some torque with a driveshaft from driveshaft specialists.

    Ive decided to just install the new ujoint on my bad slip yoke for now. I...
Results 26 to 50 of 100
Page 2 of 4 1 2 3 4