Search:

Type: Posts; User: Lazeum

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    872

    That's the thread...

    That's the thread we're talking about on hbz ;)

    Here are the changes we've made to quiet things down.
    The rockers were not sitting straight on top of the lash pads. This solution could work...
  2. Replies
    35
    Views
    2,844

    Perfect! I'll keep in touch with him then.

    Perfect! I'll keep in touch with him then.
  3. Replies
    83
    Views
    2,138

    I feel for you. You've got all the cold we did...

    I feel for you.
    You've got all the cold we did not get in Europe this year. Not even one snow flake to be seen this year. I had to grind ice from my windshield maybe 3 times this year only in the...
  4. Replies
    35
    Views
    2,844

    Hi Andreas, I'll check it out with David or Sean...

    Hi Andreas, I'll check it out with David or Sean (not sure who's your contact afterall). Thanks for your effort! It seems to be great work.
  5. Replies
    35
    Views
    2,844

    I'm in contact with the person in France, we're...

    I'm in contact with the person in France, we're all part of the same club ;)
    I'll keep an eye on your progress. Keep up the good work!
  6. Replies
    35
    Views
    2,844

    Looks great! If you're going to sell some, you...

    Looks great!
    If you're going to sell some, you can put me on the list!

    I've never disassembled the tacho. Do you believe there's a way to change the odometer also to fit kph instead of mph? have...
  7. Replies
    16
    Views
    731

    I'm running distributorless system so I'm out of...

    I'm running distributorless system so I'm out of the picture here but I'm able to control engine load advance with TPS.
    At very low load state at steady speed (=max vacuum), my engine is happy with...
  8. Replies
    37
    Views
    1,878

    I've got a Mallory pump 4070LP, it is quiet (you...

    I've got a Mallory pump 4070LP, it is quiet (you can barely hear it at idle) but I've never been able to get more than 2psi out of it for some reason no matter what I was doing to get higher...
  9. Are the throttle plate closed completely when...

    Are the throttle plate closed completely when you're at idle? Is the linkage ok and free to move within their entire range?

    Timing at idle seems very low to me. I'm running 20 with 9.5:1 CR,...
  10. Replies
    10
    Views
    453

    Welcome here! I used to live in Troy/Birmingham...

    Welcome here!
    I used to live in Troy/Birmingham MI. It took me 4 years to find a good condidate locally. At the end, it was all worth it but you might want to look also elsewere for a proper car.
    ...
  11. Replies
    35
    Views
    2,844

    If the fitting is good, I could also be...

    If the fitting is good, I could also be interested.
    Being part of French forum, where more and more Z are imported from the Z, I could foresee some interest.
  12. The 1750 would be also on my list. I'm trying to...

    The 1750 would be also on my list. I'm trying to find a different solution than yours: get some space and get te Z AND the Alfa :)
    Dreaming is not forbidden, it gives me a goal for the future.
    ...
  13. Replies
    22
    Views
    1,577

    Look for REDDAT on the forums (here, hybridz,...

    Look for REDDAT on the forums (here, hybridz, zcar, etc.) and on the web and you'll see what people think about him.
    ...
  14. Replies
    4
    Views
    418

    Welcome and definitely spend some good time...

    Welcome and definitely spend some good time reading & learning about Z's.
    There's tons of knowledge here so you can take a wise decision and get a good car to start with. As an old car, it will...
  15. Your best tool for this job would be to get the...

    Your best tool for this job would be to get the following manual. Everything is detailed inside.
    It is not difficult but you have to take your time, get the right tools and don't forget anything.
    ...
  16. Thread: Engine whine

    by Lazeum
    Replies
    10
    Views
    707

    My alternator/fan belt was undersized vs. my...

    My alternator/fan belt was undersized vs. my pulleys.
    My engine was not stock, as a result, crank pulley needed a 10mm wide belt while alternator & fan needed 13mm. 10mm belt fit but it hit the...
  17. Thread: Goodbye Poly

    by Lazeum
    Replies
    20
    Views
    1,958

    Some bushings are more critical than others...

    Some bushings are more critical than others regarding ride and confort.

    For steering feel, T/C rod busings, steering coupler and rack bushings are the most important.
    Other bushings are mainly...
  18. Replies
    35
    Views
    2,844

    I would be interested as well if we could find...

    I would be interested as well if we could find one :)
    I think your best bet would be to find a speedometer in km/h in Europe.

    One alternative that would be cool is to just replace the "front...
  19. Replies
    6
    Views
    474

    I've shipped my Z from Baltimore to France when I...

    I've shipped my Z from Baltimore to France when I moved back to Europe.
    Stereo, cover filter, Original Datsun key ring were gone on my Z, luckily, it was the only issue found. Nothing too dramatic....
  20. I'm glad to read that :) With 0 load or very...

    I'm glad to read that :)
    With 0 load or very little (like feathering the throttle pedal), you should have no knock. Most likely some noise has triggered the sensor: valves, exhaust leak, etc.

    A...
  21. Replies
    12
    Views
    471

    Head bolt torque is never related to gasket. It...

    Head bolt torque is never related to gasket. It is always related to bolt specs.
    I would get new head bolts, either from Nissan or from ARP. It's a cheap insurance for the future. ARP set is around...
  22. Replies
    12
    Views
    471

    My P79 head complete with head cover was recorded...

    My P79 head complete with head cover was recorded at 70 lbs.

    You can do it on your own but make sure you protect very well the fender in case you have an issue during transfer. If you can have...
  23. Replies
    18
    Views
    1,103

    It looks already great, even with the "not so ok"...

    It looks already great, even with the "not so ok" pictures. Good job. I need to tackle such job as well. I know how now, thanks! :)
  24. So you've got what's needed to make your engine...

    So you've got what's needed to make your engine run properly :)
    Getting low timing would not help, especially if you're breaking in the engine. Give it what it needs. Regarding knock, it happens...
  25. Your timing seems not appropriate to me. I'm...

    Your timing seems not appropriate to me.
    I'm running a much more conservative setup with CR at 9.5:1, quite aggressive cam from Rebello for the street with some overlap (don't have numbers, Rebello...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4