Search:

Type: Posts; User: madkaw

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    3
    Views
    911

    2010 Zcon was HOT! I don't care and I will b...

    2010 Zcon was HOT!
    I don't care and I will b there if it kills me getting my car back on the road again
  2. Replies
    20
    Views
    3,594

    You can do the old blow thru test to see if the...

    You can do the old blow thru test to see if the needle is closing off the flow.
  3. Replies
    20
    Views
    3,594

    So when you opened up lid on that float was it...

    So when you opened up lid on that float was it high?
    Make sure your needle and seat are sealing. Make sure the needle assembly is tight in the housing and fuel is not bypassing around the threads
  4. Thread: Stroked 240z

    by madkaw
    Replies
    2
    Views
    1,856

    Got to love that sound:)

    Got to love that sound:)
  5. Replies
    1
    Views
    387

    Very nice indeed

    Very nice indeed
  6. Replies
    18
    Views
    3,848

    Waiting for front blinker assemblies!!!

    Waiting for front blinker assemblies!!!
  7. Replies
    5
    Views
    521

    We won't hold the jersey part against you....

    We won't hold the jersey part against you.
    Welcome
  8. Replies
    11
    Views
    778

    Digging into it for a known problem or just...

    Digging into it for a known problem or just thinking refresh?
    What's your experience? If your asking how long it takes to remove the head then I would assume you have little Z experience
    Like Zed...
  9. Replies
    28
    Views
    2,257

    pics of carnage

    So here are some pics of the cylinder bores. Also pics of my Chevy Sonic pick-up truckLOL
  10. Replies
    12
    Views
    905

    Usually the harness is okay except for areas...

    Usually the harness is okay except for areas subject to heat or direct weather. I would clean and replace only where necessary . Blades or pins I tried cleaning with sandpaper or mini file to get...
  11. Replies
    19
    Views
    1,649

    Just the fact that he e-mailed me back right away...

    Just the fact that he e-mailed me back right away was a plus in my book .
    I've been waiting a week or so for Schneider to call me.
    PM me for a cell number, I hate the messenger on this site.
  12. Replies
    19
    Views
    1,649

    Cliff, Recently discovered DatsunZfiberglass ....

    Cliff,
    Recently discovered DatsunZfiberglass . The guy makes it all it seems, but the website kin of sucks. I did e-mail him and he did respond. Might be worth a look
  13. Replies
    28
    Views
    2,257

    Well the block and pistons are at the machinist....

    Well the block and pistons are at the machinist. A cursory inspection by him and he said I had nothing to worry about. He agreed to measure everything out and thought a good hone and new rings and I...
  14. ummmm, not that I know from first hand experience...

    ummmm, not that I know from first hand experience or anything, but I heard you can get two rubber marks when launching.
  15. Replies
    51
    Views
    3,492

    I have to agree with Carl, it's American greed...

    I have to agree with Carl, it's American greed that dictates how stuff is made. If the vendor says' make it as cheaply as possible' , that's what the Chinese manufacture will do. It's the guy...
  16. That's funny Charles. That kind of LSD may or may...

    That's funny Charles. That kind of LSD may or may not get you better handling of stuff-lol
  17. Replies
    9
    Views
    843

    Ummm- doesn't Nissan still sell those seals?

    Ummm- doesn't Nissan still sell those seals?
  18. timing #'s?

    timing #'s?
  19. Kind of weird the mn47 head gave such low CR...

    Kind of weird the mn47 head gave such low CR numbers .
    The pistons should take effort to push up, but try some trans fluid and see what it does.
    How do you just find a mn47 head in the junk yard....
  20. Replies
    4
    Views
    1,117

    SHAMELESS! If I were you I would take it to Leon....

    SHAMELESS! If I were you I would take it to Leon. To have a Z expert in your backyard is priceless. There are many on this site that would love to have that advantage. It will save you time and money...
  21. So you lost power after going to the 47 head? Or...

    So you lost power after going to the 47 head? Or it had 'scary' power with which head?
    Don't forget the basics, a good tune is everything. Done a valve adjustment since installing the rebuilt head?...
  22. Replies
    38
    Views
    1,745

    Why wouldn't it?

    Why wouldn't it?
  23. Replies
    9
    Views
    614

    Really no reason for your car to idle that fast...

    Really no reason for your car to idle that fast in the first place, the cam is not that big. You probably have a vacuum leak as suggested. Search you tube for troubleshooting vacuum leaks
  24. Those cam specs look like my Schneider Cam stage...

    Those cam specs look like my Schneider Cam stage 2 -which should idle like normal-not 1100 rpm.
  25. Replies
    28
    Views
    2,257

    Look at the head pic of the combustion chambers....

    Look at the head pic of the combustion chambers. The last three cylinders I had most of the issue, but #2 fouled on me also.You can see the difference looking at the valves from a distance. The...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4