Search:

Type: Posts; User: JLPurcell

Page 1 of 4 1 2 3 4

Search: Search took 0.06 seconds.

  1. Adam, I did scratch one of the rear springs...

    Adam, I did scratch one of the rear springs putting them back on. The front was much easier once I finished the learning curve on the rear. I will touch it up, and this is going to be a driver. I...
  2. It's a roller again!

    Good day today, had the day off and was able to get the springs and axles back under the frame today.;) All new bushings and new shackles and pins with grease zerts.:laugh: Engine in by end of...
  3. That is the expanded steel rock guard that goes...

    That is the expanded steel rock guard that goes in front of the radiator. Same material as the JDM front grill for the 240Z.
  4. Land Cruiser frame back from powder coat!

    Here are a few photos of the frame back from powder coat.LOL I just finished blasting and painting the rear differential and springs (soaked on the black gloss paint). Will start assembly tomorrow,...
  5. New Member!...

    New Member!!

    This link is to the Land Cruiser Club it has more detail and will begin to have much more now that I have the frame back. Thanks for you kind comments and your interest. JLP
  6. Frame back from powder coat!

    I just picked up the frame and parts from powder coat.:cool: I as giddy as a 16 year old seeing their first car! I will post photos soon.LOL
  7. First test part cast!

    I have cast the first test part. The mold is great and the part is great with all of the fine detail.:love: I will have to buff the reproductions out or buff one out and make a new mold due to some...
  8. Replies
    22
    Views
    1,316

    They are a re-list no bids at $1,600. first time.

    They are a re-list no bids at $1,600. first time.
  9. Casting new horn button.

    While waiting for my frame to get back from powder coat I am going to try and reproduce the horn button. There are no NOS available and I have a good part to make a mold with.;) I have ordered the...
  10. No, to be honest I do not know that much about...

    No, to be honest I do not know that much about powder coat. I am dropping off the frames, pans etc... this morning. The company has a large automated oven that will do large parts, they come highly...
  11. I have wrestled with this for the last few months...

    I have wrestled with this for the last few months and my hotrod buddies have convinced me to give powder coat a try.
  12. Frame finally ready for powder coat!

    The frame is now ready for powder coat.;) I have mocked up, fabricated and installed all of the brackets etc... for the power steering upgrade. The front splash panel is modified for the new steering...
  13. Replies
    8
    Views
    704

    Phil, You can take a set to a plating shop they...

    Phil,
    You can take a set to a plating shop they can weld up the holes prior to plating.
    JLP
  14. Thanks Phil

    Thanks Phil
  15. Phil thanks for your reply. I need a couple of...

    Phil thanks for your reply. I need a couple of nuts that will hold the face plate in place. Original would be great but not necessary.
  16. Looking for radio face plate retaining nuts.

    Does anyone have a couple of early (Series 1) radio face plate retaining nuts they would sale?;) The nuts that go on the tune and volume pots holding the face plate in place. JLP
  17. No it does not have a sunroof installed.

    No it does not have a sunroof installed.
  18. Looking for a steering part for 1st Gen Z

    I need the shaft that goes between the steering column and the steering rack. I need for the U joint to be in good tight condition. Anyone have one for sale?:ermm:
    JLP
  19. Replies
    22
    Views
    1,149

    A dead one at the moment!

    A dead one at the moment!
  20. Local Car broker called me about HLS30-001345

    I took a look at this today here in Richmond. A local car broker picked it up from the owner since 1972. She had rust repaired and paint (purple) in 1984. Matching Engine, 75000 miles, He is trying...
  21. Worked on power steering conversion and media blasting of frame today!

    I am working to get the frame and drive-train caught up to the body so I have a place to sit the tub when the paint is complete!
    734277342873429
  22. Replies
    12
    Views
    1,638

    Perfect, I have a home near Cookville, TN. I am...

    Perfect, I have a home near Cookville, TN. I am looking forward to Memphis!
  23. Thread: Zcon 2015

    by JLPurcell
    Replies
    6
    Views
    575

    Indiana convoy? ;-)

    Indiana convoy? ;-)
  24. Thread: Zcon 2015

    by JLPurcell
    Replies
    6
    Views
    575

    Memphis, I can do that! Gives me a goal to get...

    Memphis, I can do that! Gives me a goal to get back on the details of my Z!
  25. Worked on the original F Engine refresh today!

    Almost ready to close it up! Waiting for a few parts from powder coat and plating ;-)
    7325173252
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4