Search:

Type: Posts; User: philbar73

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    307

    I did a few searches and found :speedometer...

    I did a few searches and found :speedometer bounce" could be the cable or the gear. I think its the cable. I had cleaned it out and lubed it with cable lube when I was putting it back together. Cable...
  2. Replies
    2
    Views
    307

    Speedometer jumping

    At low speed my speedometer jumps. I think its the speedometer cable. Any thoughts?
  3. I have a 73 build date of 6/73

    I have a 73 build date of 6/73
  4. It could be a bad ignition switch. My car was off...

    It could be a bad ignition switch. My car was off the road for 24 years. When I put it back on the road the starter would turn in the accessory position. I replace the ignition switch and all was...
  5. Replies
    11
    Views
    491

    I think there should be a spacer between the fan...

    I think there should be a spacer between the fan and water pump. I'm not positive but that would give you a little more clearance if I'm correct. I've worked on a lot of cars so I could be mistaken....
  6. Thread: NYC members

    by philbar73
    Replies
    4
    Views
    468

    Post some pics

    Post some pics
  7. Thread: NYC members

    by philbar73
    Replies
    4
    Views
    468

    What do you have to do? I'm on Long island,

    What do you have to do? I'm on Long island,
  8. Replies
    4
    Views
    307

    I think you need less teeth so it will turn faster

    I think you need less teeth so it will turn faster
  9. Replies
    18
    Views
    801

    One of my windows was doing the same thing. I put...

    One of my windows was doing the same thing. I put a few washers under the regulator when I mounted it and the problem went away. The broken plastic washers didn't cause a problem in the operation of...
  10. Replies
    4
    Views
    575

    The output (speaker leads) measure .9 ohms. The...

    The output (speaker leads) measure .9 ohms. The only thing I can think of is I'm testing a winding on a transformer. If it was a capacitor I would think that I would see the reading changing. It...
  11. Replies
    4
    Views
    575

    The radio works fine. I want to look at the...

    The radio works fine. I want to look at the output stage before I hook it up to a power amp so I don't damage it. I think its transform isolated but do not want to make a mistake.
  12. Replies
    4
    Views
    575

    Schematic for Hitachi KM-1520ZD needed

    I'm looking for the Schematic for a Hitachi KM-1520ZD radio. Can anyone help?
  13. Now that I have driven the car a few times, I...

    Now that I have driven the car a few times, I still have a little bit of gas dripping. It is greatly improved.
  14. Thread: Headlights

    by philbar73
    Replies
    7
    Views
    661

    I had alot of problems with switchs and...

    I had alot of problems with switchs and conectors. I used Deoxit 100 Hosa Caig DeoxIT D100, Deoxidizer Aerosol Spray, 2 oz D100S2 on the switches and conectors and everything works.
  15. Replies
    18
    Views
    3,094

    Hi Dr 240Z. it looks like the way you set up the...

    Hi Dr 240Z. it looks like the way you set up the chokes is actual a lot less moving parts. one pivot and a few cables. Looks like a nice setup to me.
    Thanks for the good words. I love to work on my...
  16. As I suspected, the fuel pressure drops...

    As I suspected, the fuel pressure drops immediately when I turn off the RX7 pump. I guess it’s a centrifugal pump and has no check valve. I remember the old fuel pump and regulator held pressure for...
  17. Do your carbs drip when you turn it off or all...

    Do your carbs drip when you turn it off or all the time? I had a 15lb pump and a regulator set to 4lb. They ran fine but dripped after i turned off the car. The only thing i can think of is there was...
  18. I changed the fuel pump to a low pressure RX7...

    I changed the fuel pump to a low pressure RX7 pump as suggested in many posts on this site. The gas dripping stopped when I turn the car off. I think the old electric fuel pump held pressure in the...
  19. Replies
    18
    Views
    3,094

    I set up the chokes in the 80's so the drawings I...

    I set up the chokes in the 80's so the drawings I made of the parts are long gone.
    I couldn’t tie the stock choke levers directly together with a cable because the cable would interfere with the...
  20. Replies
    9
    Views
    2,157

    3 barb fuel rail for L6

    I saw this thread pop up and never posted a picture of the fuel rail instaled on the car.
  21. Replies
    95
    Views
    6,800

    Thanks everyone. The RT mount and GM mounts are...

    Thanks everyone. The RT mount and GM mounts are in. All went well; I wish I had a lift. Maybe 3 hours of work. The only tough spot was breaking the 17MM (big bolts) that held the old mount to the...
  22. Replies
    95
    Views
    6,800

    Thanks again for all the help. I have the mount...

    Thanks again for all the help. I have the mount in hand. Can anyone tell me what two nuts and bolts I will need to bolt the GM mount to the diff so I will have everything ready when I lift the car...
  23. Replies
    95
    Views
    6,800

    Thanks Diseazd for the fast response. I'm looking...

    Thanks Diseazd for the fast response. I'm looking forward to driving with a solid drive train. I've been real easy on it because of the bang in the back. Looks like less them an hour of work the way...
  24. Replies
    95
    Views
    6,800

    I'm just finishing a rebuild, restore on my 1973...

    I'm just finishing a rebuild, restore on my 1973 240Z. I have a big clunk form the rear end when I shift. The drive shaft and axils are solid, very little movement in the universal and axils so I’m...
  25. Replies
    21
    Views
    3,927

    I had the same problem; the pressure would be...

    I had the same problem; the pressure would be good at the start then drop way off when warm. The sending unit was the original, it was 39 years old. I put in a new sending and the pressure looks...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4