Search:

Type: Posts; User: 280zzzzz

Search: Search took 0.01 seconds.

  1. i see that zcs in arizona has Brake Fluid Switch...

    i see that zcs in arizona has Brake Fluid Switch 12302302 @ 109.99 and np valve listed 12202401 price tbd
    used - but better than nothing...
  2. Replies
    0
    Views
    337

    Brake Hard Line Sources

    I stumbled across a source of Brake Hard lines from Master Cylinder to Brake Switch and BrSw to NP Valve a while back when I was searching for a Brake Booster. I am sure I saw prebent replacement...
  3. Replies
    9
    Views
    604

    I was under the beer can holder (relay bracket)...

    I was under the beer can holder (relay bracket) myself today. My August 76 model (has sloped interior rear package shelf) has the same - 2x Fusible link Holders / Voltage Regulator /Condenser / and...
  4. Replies
    0
    Views
    1,499

    Fuel Pump for Carbs - Pipe Fittings

    I am hoping someone has run into this before. I am swapping to DCOE45s from injection on #359550 '77 280Z - I bought an Advanced Fuel Products PN 56-012 fuel pump for carbed RX7s from BD. ...
  5. Replies
    20
    Views
    1,318

    I just recieved 2 fenders from Nissan - Made in...

    I just recieved 2 fenders from Nissan - Made in Japan. "Packed" in nothing but bubblewrap Japanese Nissan Graphics - but perfect condition. Ordered from Applewood Heritage Nissan - Kobi...
  6. Replies
    3
    Views
    443

    Heh Thanks ZED - That's good advise, I knew...

    Heh Thanks ZED - That's good advise, I knew I was in trouble when I answered my own enrty... ;)
  7. Replies
    3
    Views
    443

    search - fuel pump check valve - by jazfe -...

    search - fuel pump check valve - by jazfe - Thanks OneFastWoman
  8. Replies
    3
    Views
    443

    280Z aug 76 fuel pump - check valve ?

    I am in the process of swapping to carbs, and could use some expertise..... So far I've boiled out the fuel tank, replaced all of the old rubber lines, and have circulated a gallon of injector...
  9. Zed I'll try again at "TheOffice" where the...

    Zed I'll try again at "TheOffice" where the connection is better than the shop. You are right a lot of good people go the extra mile..
    Thanks Again. mel
  10. Replies
    5
    Views
    849

    Thanks for the reply re:rear hatch mechanism. My...

    Thanks for the reply re:rear hatch mechanism. My assembly turned out to be THE rustiest thing on the car - removal involved removal of interior and exterior trim panels and eventually a dremel...
  11. Thanks All for your comments. I have not been...

    Thanks All for your comments. I have not been able to find a 77 manual, and have no luck downloading one yet. It has the angled rear deck-and 5speed. The carpartsmanual is a great resource, along...
  12. Serial Number _vs_ Factory Service Manual Information

    I would appreciate any comments on this. As I rebuild my 280 all the ID Tags / VIN indicate it is #359550 dated August 1976. I have owned it since 1978. I have run into several instances where the...
  13. Replies
    61
    Views
    3,834

    LH pin, in vise, full length tap tap tap - fell...

    LH pin, in vise, full length tap tap tap - fell right out on the floor... think to myself what's the big deal..... RH one not so much, soaked 2 weeks in penetrating oil - made removal tool with...
  14. Replies
    5
    Views
    849

    I know this is an OLD thread - but for those...

    I know this is an OLD thread - but for those struggling with this.... remove rear trim panel from inside - I had to pull back carpet and remove the rear hinged floor section to get panel off. Remove...
Results 1 to 14 of 14