Search:

Type: Posts; User: geezer

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Hello Jerry...this is as good a place as any for...

    Hello Jerry...this is as good a place as any for a group meeting. Most of the afflicted frequent these pages.
    I too have a problem (but only in the eyes of others).
    I only buy Z parts to better...
  2. Replies
    54
    Views
    2,984

    I had to open that seam up to clean/blast and...

    I had to open that seam up to clean/blast and reweld, re-seal as well. It was/is common practice to apply seam sealer between all metal mating surfaces before spot welding. It expanded and cured...
  3. Thanks for the link and attachment Blue. It is an...

    Thanks for the link and attachment Blue. It is an interesting topic that at this point, I can only partially comprehend but enjoy reading and hearing the results of the testing just the same.
  4. Interesting chart. At first glance that chart...

    Interesting chart. At first glance that chart would seem to prove the old adage, "less is more". Do you have the link to the article with any descriptions of statistical models? It must be a science...
  5. Replies
    54
    Views
    2,984

    I welded new metal in for my cowl chimney repair...

    I welded new metal in for my cowl chimney repair and flowed some two part epoxy similar to the type shown in this link. It bonded permanently to the epoxy primer, creating a perfect, tougher than...
  6. Have you made a visual comparison between the old...

    Have you made a visual comparison between the old and new caps and rotors? If so and nothing is readily apparent, try putting the old rotor back in and if that does nothing try swapping the old cap...
  7. Replies
    54
    Views
    2,984

    LinParkFL, if you read that thread I linked to, I...

    LinParkFL, if you read that thread I linked to, I mentioned using one of the adhesive panel bonding products. They have come a long way in recent years and I'm convinced that a cowl repair could be...
  8. Replies
    10
    Views
    515

    On my 4X4 trucks that were run mercilessly in...

    On my 4X4 trucks that were run mercilessly in extreme weather and regularly submerged in the muck, I would always run a small amount of axle grease around brake fittings but only after they had been...
  9. Replies
    54
    Views
    2,984

    68650686446864568646686476864868649 There are...

    68650686446864568646686476864868649

    There are some great solutions and work to solve this problem shown in this thread.
    Here's a link to an earlier thread with some ideas and great pics. Member...
  10. I think it is. Decades before Nissan built our...

    I think it is. Decades before Nissan built our steering wheels Henry Ford was trying to develop the technology as well but he was using hemp fibers.
    Wonder what the weight factor is. I could use a...
  11. Replies
    6
    Views
    788

    Chris, what is the publication date of your copy?...

    Chris, what is the publication date of your copy? All these years later it does seem to be somewhat counter productive, Pub.No.C-235 being dated March of 1974, covering the years 1969-...
  12. Replies
    6
    Views
    788

    I have a xeroxed copy of the Nissan Fairlady-Z...

    I have a xeroxed copy of the Nissan Fairlady-Z Parts Catalog Model S30 PS30 1970. It is dated 1971, 3. It has a few noticeable differences, when compared to Kat's original copy (dated later). We...
  13. Replies
    8
    Views
    701

    Remove a sparkplug and feed in a short length of...

    Remove a sparkplug and feed in a short length of nylon rope. Torque to spec after the rotating assembly cannot turn.
  14. Replies
    16
    Views
    2,338

    63981

    63981
  15. Replies
    9
    Views
    830

    Greg, I believe you could very well be correct....

    Greg, I believe you could very well be correct. It certainly is not beyond the realm of possibility. During my career with another automobile manufacturer, I witnessed dozens of instances where stock...
  16. Replies
    9
    Views
    830

    There were replacement air cleaner housings sold...

    There were replacement air cleaner housings sold over the counter at the parts department that were blue. So they would still be correct, I think.
  17. Replies
    23
    Views
    1,131

    I can appreciate the amount of effort that you...

    I can appreciate the amount of effort that you have put into the creation of this chart but as Alan has pointed out, in order to be complete, and to cover all model designates another approach would...
  18. Replies
    25
    Views
    1,737

    If only I had the time. A wall poster showing...

    If only I had the time.

    A wall poster showing the entire S30 family tree would be a wonderful thing. Especially if it was done in a manner that would explain the reasons for and describe each...
  19. Replies
    25
    Views
    1,737

    I don't believe the average consumer or Z...

    I don't believe the average consumer or Z enthusiast in the US ever had much of a need or desire to know what the individual market designations were/are. It is very important in the manufacturing...
  20. Replies
    15
    Views
    1,173

    I am pointing out that there are several products...

    I am pointing out that there are several products available for the purpose of lubricating and fitting rubber. That particular one I linked to is offering free samples. I wasn't recommending you...
  21. Replies
    15
    Views
    1,173

    Don't underestimate the flexability afforded with...

    Don't underestimate the flexability afforded with pre-heated rubber and the lubrication properties of products designed for fitting rubber without damaging paint. For several years I used a product...
  22. Replies
    19
    Views
    2,756

    LOL Yeah, ask them if they want to go for a spin!...

    LOL Yeah, ask them if they want to go for a spin!

    :classic:Alright, good stuff, glad to see it finished. Looks great!
    You can drill more holes through the heads to create more stop positions.
    ...
  23. Replies
    7
    Views
    1,471

    Up to 06/71, end of the '71 model year part...

    Up to 06/71, end of the '71 model year part number 55450-E4101

    From 07/71 to 07/73 the '72 model year part number 55450-E8300
    My scanner is down, Dan is correct, there are 8 different modified...
  24. Replies
    5
    Views
    744

    I bought one from zeddfindings. It was very...

    I bought one from zeddfindings. It was very pricey and was a total disappointment. It is flat the total length of the piece with no compound bow like the original. It needs to be worked on an english...
  25. :classic:Thank you Takeuchi-san, those are very...

    :classic:Thank you Takeuchi-san, those are very nice views of the 100L fuel tank. Even though I have never seen one in person, it certainly would be instantly recognizable if I did.
    Great spring...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4