Search:

Type: Posts; User: Ed

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    1,156

    What are you using to try and straighten the...

    What are you using to try and straighten the bracket? I would make something specific for the job. Use those fab skills. Then put the car on a lift so you can really get under there. Put a 5' cheater...
  2. Thread: masking valve cover

    by Ed
    Replies
    3
    Views
    674

    You should try masking carefully but I think it...

    You should try masking carefully but I think it would be a lot of work. Personally I would paint the whole thing then after it was dry take some 220 grit wet sand paper and carefully start removing...
  3. Replies
    20
    Views
    1,278

    The # 2 location the cam gear is to compensate...

    The # 2 location the cam gear is to compensate for a timing chain that is old and stretched out. Refer to your FSM. There are diagrams that show where your timing marks should be. To me it doesn't...
  4. Replies
    20
    Views
    1,278

    Since you recently completed a rebuild you should...

    Since you recently completed a rebuild you should double check that the assembly went as required. Start with the timing. Put your engine at TDC and make sure the distributor shaft is in the right...
  5. Replies
    7
    Views
    414

    Any hardware store it's called "rope caulk" not...

    Any hardware store it's called "rope caulk" not as sticky as the factory black stuff but it works just as good and cleans up much easier.
  6. Replies
    29
    Views
    7,858

    Bahh, bad ass is all i've got to say. Looks Good!

    Bahh, bad ass is all i've got to say. Looks Good!
  7. Replies
    7
    Views
    771

    Just goes to show you that once you've been...

    Just goes to show you that once you've been bitten by the "Z" nothing else matters!
  8. Replies
    10
    Views
    1,897

    Go with a 2 1/2 or smaller. Tell him you want...

    Go with a 2 1/2 or smaller. Tell him you want aluminized steel. welded at all the seams. Resonator in the middle before the split then some dynomax or whatever your choice of muffler at the end. If...
  9. Thread: On the road again.

    by Ed
    Replies
    11
    Views
    1,135

    Ha, i did it again. Now I'm living in Louisiana....

    Ha, i did it again. Now I'm living in Louisiana. Gotta love them shrimp!
  10. Thread: Proper dash care??

    by Ed
    Replies
    15
    Views
    1,456

    turtle wax has a product in a green bottle...

    turtle wax has a product in a green bottle formula 2000 or F21 that supposedly has no silicone
  11. Replies
    7
    Views
    1,466

    dynomat or brown bread all the same

    dynomat or brown bread all the same
  12. Replies
    14
    Views
    3,861

    Hey, I forgot about this post. Hope it works out...

    Hey, I forgot about this post. Hope it works out for you. Remember to create a mirror image of the templete for the opposite side.
  13. Thread: 2008 Nationals

    by Ed
    Replies
    54
    Views
    4,931

    Does anyone know the dates? Or a link?

    Does anyone know the dates? Or a link?
  14. Replies
    29
    Views
    2,366

    I've heard this is not a good idea. If the car...

    I've heard this is not a good idea. If the car isn't run at full operating temperature at highway speeds for atleast 30 minutes, condensation in the fuel system, exhaust system, cooling system and...
  15. Thread: Head Removed

    by Ed
    Replies
    4
    Views
    1,088

    What type of straight edge did you use on the...

    What type of straight edge did you use on the head? You need one that will go from one end to the other AND be precise. Take it to a shop and have them use a precision straight edge and pressure test...
  16. Replies
    1
    Views
    1,033

    You can get the correct size freeze plugs at any...

    You can get the correct size freeze plugs at any auto parts store.
  17. Thread: battery tray

    by Ed
    Replies
    4
    Views
    733

    first find a donor tray. Then once you know what...

    first find a donor tray. Then once you know what you have start cutting.
  18. Replies
    2
    Views
    672

    Stay away from the 4 bbl. Less HP than stock...

    Stay away from the 4 bbl. Less HP than stock S/U's.
  19. Replies
    5
    Views
    761

    Try your local auto parts store. If they can't...

    Try your local auto parts store. If they can't get it then go to your local Nissan dealer. Then go to mail order MSA, Black Dragon or ebay.
  20. Thread: Cold start issues

    by Ed
    Replies
    8
    Views
    896

    I don't think your problems are related to any...

    I don't think your problems are related to any recent work that you have done. First off let me ask what type carbs do you have (flat tops or round tops)? Second what type of ignition are you...
  21. Replies
    116
    Views
    32,319

    Mine are the sloted mags, I had them machined...

    Mine are the sloted mags, I had them machined finished with the slots painted to match the rear tail light trim.

    BTW how do you load a picture from your computer onto the post so it doesn't show...
  22. Replies
    2
    Views
    1,259

    Ontario, Canada Z club car show

    Haven't noticed this advertised anywhere.

    Ontario, Canada Z club car show August 26th, 2007.

    http://www.ontariozcar.com/eventz/EventCalendar/Z-FEST2007%20Flyer.pdf

    One of the biggest shows...
  23. Thread: Gunmetal Panasports

    by Ed
    Replies
    11
    Views
    1,206

    ARghhh, that blows. Well atleast you will get...

    ARghhh, that blows. Well atleast you will get them sooner or later. Have you checked with MSA? Do they have a backorder?
    I think you should let me run them for a bit to make sure they will work...
  24. Thread: Illegal window tint

    by Ed
    Replies
    22
    Views
    2,532

    The officer told me that since 1992 the law...

    The officer told me that since 1992 the law changed to where the drivers and passengers windows werent able to be darker than 75%. I've had the car in NY since 2002. I tinted the windows in 2003.
  25. Thread: Illegal window tint

    by Ed
    Replies
    22
    Views
    2,532

    I don't know what the fine is. Ticket doesn't...

    I don't know what the fine is. Ticket doesn't say. My options are to plea guilty and mail in the ticket. I assume I'll get the fine afterwards. Or to plea not guilty and go to court.
    BTW it was...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4