Results 1 to 3 of 3

Thread: Difficulty Removing Float Bowl Lid for a 72 240Z SU Carburetor

  1. #1
    Registered User
    Member ID
    CZCC-29806
    Join Date
    Oct 2013
    Location
    Grand Prairie, Texas
    Posts
    1

    Default Difficulty Removing Float Bowl Lid for a 72 240Z SU Carburetor

    Greetings. I'm new to the Z world. Just purchased my 1st, a 1972 240Z and it has SU carburetors. The car sat for a couple of years before I purchased it and the floats were stuck with valve open.

    In the attempt to remove the bowl cover, I buggered up the float. There is a flange off the side of the SU carb that hangs right over the bowl cover. Multiple attempts to turn the lid to get better clearance didn't help, and the tension of the float on the sides of the bowl during this process popped the float right off of its lever arm. A new float will be ordered.

    So, like, what's the trick? If I have to make multiple adjustments to get the float/fuel level set right, this will be a very difficult process with that flange off the side of the carburetor in the way.

    If you know the way, please respond.

    Thanks,

    Bryan
    Grand Prairie, Texas

  2. #2
    Registered User Stanley's Avatar
    Member ID
    CZCC-24191
    Join Date
    Apr 2011
    Location
    Redondo beach
    Posts
    641

    Default

    Helps to drain out the gas and turn the lid 90 degrees. Don't need to use any muscle on it. The floats are fairly tough so when you get it out you can probably straighten it up enough to use. The float bowl valves have a rubber tip that should have a sharp conical point - if not they're shot. New ones are available from MSA and elsewhere. Lot's of information on this site. ZTherapy has a video.
    The flange on the side is no problem if you drain the gas.

  3. #3
    Registered User
    Member ID
    CZCC-4044
    Join Date
    Apr 2003
    Location
    Denver
    Posts
    1,008

    Default

    It helps to take the fuel line off then twist the lid.

    Now if you are adjusting float levels using a sight glass method(clear plastic tubing) use a longer fuel line so you can manipulate the lid and hose so there isn't any tension with the fuel line.
    things will only bother you if you let them.

    82 280zxt 4 spd auto
    73 240z--lsd, cv axles
    short throw info

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 3 screw su float bowl lid ear lengths
    By putmattaway in forum Help Me !!
    Replies: 4
    Last Post: 04-08-2013, 08:19 AM
  2. Gas Depth in Float bowl, when excluding float volume
    By hogie in forum Carburetors (S30)
    Replies: 36
    Last Post: 05-14-2010, 04:08 PM
  3. Float Bowl Vent
    By Xargon321 in forum Carburetors (S30)
    Replies: 0
    Last Post: 08-04-2003, 05:52 PM
  4. Float bowl and needle
    By Doehring in forum Carburetors (S30)
    Replies: 8
    Last Post: 07-21-2003, 07:27 AM
  5. Float bowl on '70-'71 SU
    By gpitman in forum Engine and Drivetrain (S30)
    Replies: 1
    Last Post: 12-08-2000, 07:43 AM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •