Search:

Type: Posts; User: bjhines

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    29
    Views
    4,547

    I have to disagree with the issues of pad...

    I have to disagree with the issues of pad material transfer. This is made out to be more of a problem than it is.
    I have run damn near every combination of brake parts ever used on S-30s. ON TRACK...
  2. The factory fuel rail has a restricted bypass...

    The factory fuel rail has a restricted bypass that was there to aid in purging the vapors out of the lines during hot starts.
  3. Replies
    5
    Views
    1,061

    there are guys gettting 250HP out of mildly built...

    there are guys gettting 250HP out of mildly built L-28s with good indution and exhaust systems. This should be close.
  4. Replies
    1
    Views
    972

    The electrical system has 2...

    The electrical system has 2 sub-harnesses(passenger kick panel) that power the pump only when the key is in the run position and the engine is NOT running.
    The original harness only operated the...
  5. Replies
    6
    Views
    993

    The fact that the light comes on when the pedal...

    The fact that the light comes on when the pedal is applied and goes off when released means that the switch is working.
    There is no reason whatsoever to suspect failure of the switch.

    The...
  6. Replies
    20
    Views
    3,166

    Nice info there Carl. Those are the harnesses. ...

    Nice info there Carl. Those are the harnesses.
    It was my understanding that the add on kit was available to retrofit all the earlier models but was a factory installed piece on the 1973 models. I...
  7. Replies
    20
    Views
    3,166

    I am providing pics just to clear up continuing...

    I am providing pics just to clear up continuing confusion on the 1973 240Z fuel-cut harness.

    The harness has a terminal from the voltage regulator, a terminal from the starter solenoid. It also...
  8. Replies
    20
    Views
    3,166

    It is true that many previous owners have changed...

    It is true that many previous owners have changed the wiring configuration... But I have owned 2 1973 240Zs that had unadulterated wiring with the relay system I have described. I also have a 1972...
  9. Replies
    20
    Views
    3,166

    The original mechanical pump crosses over to many...

    The original mechanical pump crosses over to many other vehicles. It was originally made by Kyosan-Denki(sp). They are still available through a variety of sources including E-Bay for less than $50....
  10. Replies
    20
    Views
    3,166

    I have to chime in here on some misinformation on...

    I have to chime in here on some misinformation on the operation of the ELECTRIC FUEL PUMP WIRING. The 1973 240Z uses ONLY THE MECHANICAL PUMP during normal operation. The electric fuel pump is for...
  11. The air horns are there for several reasons. ...

    The air horns are there for several reasons.

    They smooth out the airflow entering the venturis.
    They also contribute to the overall runner length which is determined by the build specs of your...
  12. I love the Webers. These pics might give you some...

    I love the Webers. These pics might give you some more ideas.
    BTW. I used the stock fuel rail with return line, stock mechanical pump, stock vacuum control valve and PCV system. I added an electric...
  13. Replies
    8
    Views
    1,174

    It is just a doubler. It reinforces a kink prone...

    It is just a doubler. It reinforces a kink prone area in the chassis rails. Your rust issues look minor to me. I have been into quite a few S-30s for rust repairs. Yours looks pretty good in that...
  14. Replies
    7
    Views
    1,130

    That comparison to the drawing on the wall is way...

    That comparison to the drawing on the wall is way off....

    The Ford drawing has very little similarity to the Z car drawing... Give me a break... That is totally reaching for Ford Worship... The...
  15. Replies
    33
    Views
    4,330

    I am most impressed with nearly everything that...

    I am most impressed with nearly everything that TWM produces...

    I guarantee that the TWM airbox is worth every penny... PLUS!!!! the TWM airbox can be ordered with the mounting panel precut to fit...
  16. Replies
    33
    Views
    4,330

    yes... that is vacuum porting because I do drive...

    yes... that is vacuum porting because I do drive that car on the street... and it has a high overlap cam installed... The 45mm carbys with that cam make very little vac at low RPM...

    I would NEVER...
  17. Replies
    33
    Views
    4,330

    and another point about the Rebello CAI... that...

    and another point about the Rebello CAI... that works fine for a race car that is in constant high speed motion... but for a street car you need cold air when moving slowly or at a stop...

    The...
  18. Replies
    33
    Views
    4,330

    I'll tell you how sensitive the system is... ...

    I'll tell you how sensitive the system is...

    Notice in this picture i have removed the hose and simply stuck the filter on the front of the sirbox......
  19. Replies
    33
    Views
    4,330

    Well.. then.. that would be effectively a COLD...

    Well.. then.. that would be effectively a COLD AIR BOX.. with no filter on the end... I think keeping the filter on the airbox and keeping the carby airhorns free of clutter would be better...

    In...
  20. Replies
    33
    Views
    4,330

    Ohhh... The Webers AND the SUs have balance ports...

    Ohhh... The Webers AND the SUs have balance ports on the intake mounting face of the carby body... as long as these ports are inside the same airbox as the intake horns... the carbys will balance out...
  21. Replies
    33
    Views
    4,330

    Here is my ram air box... although I would use...

    Here is my ram air box... although I would use the TWM airbox in a heartbeat before I made another one of these...


    DCOE-45 series 152 with consecutive serial numbers... TWM manifold with their...
  22. Replies
    11
    Views
    2,571

    I have a lead... Nissan Pathfinder trucks... I...

    I have a lead... Nissan Pathfinder trucks... I don't know what years.. whichever ones had the reverse steering box...
  23. Replies
    11
    Views
    2,571

    I'm going to dig this one up again.... The...

    I'm going to dig this one up again....

    The datsun Rack has a 15mm 28 spline spud... you cannot use the aftermarket joints without having a set custom fabricated...

    The stock steering u-joints...
  24. Replies
    11
    Views
    1,637

    I am really enjoying them.... My wife is...

    I am really enjoying them....

    My wife is having the full sized ones printed for posterity...
  25. Replies
    20
    Views
    5,210

    The rear suspension uprights are part of the...

    The rear suspension uprights are part of the install package... they are new stampings with ears and drilled holes to mount the sway bar bushings...
Results 1 to 25 of 72
Page 1 of 3 1 2 3