Search:

Type: Posts; User: gnosez

Page 2 of 4 1 2 3 4

Search: Search took 0.01 seconds; generated 86405 minute(s) ago.

  1. Replies
    22
    Views
    1,178

    carlisle race car exhibition hall

    7120771206

    Bringing this down for the weekend. Looking forward to seeing some nice Zs. Just a driver's seat so unless you want to do what they did back in the day (throw a blanket in the seat well...
  2. Replies
    12
    Views
    631

    Not an LSD. The T5 is heavier than a 280ZX "B"...

    Not an LSD.
    The T5 is heavier than a 280ZX "B" tranny by many, many pounds.
    Sell the T5.
    Try the diff. Likely you might not be pleased using it in a street car.
  3. Replies
    10
    Views
    1,761

    Twice Pipes

    Not all twin pipes require you to cut or modify the rear lower valance
  4. Replies
    41
    Views
    2,079

    Desiccated cheerios? Put a vacuum tip up to the...

    Desiccated cheerios? Put a vacuum tip up to the vent and see if you can remove more.

    I had little bits of seat foam fly out after I turned the blower motor on high, soon followed by 2 baby mice...
  5. Replies
    3
    Views
    511

    So unless I read this wrong replacing the...

    So unless I read this wrong replacing the mustache bar won't help your weak carrier leg or bolt area issue. I have several TTT pieces in my 240 and they are very nice to say the least and I've had no...
  6. The twice pipes are not what is making your Z...

    The twice pipes are not what is making your Z loud it's your muffler(s)
  7. Replies
    37
    Views
    4,722

    So the guy in the dark sun glasses wasn't in the...

    So the guy in the dark sun glasses wasn't in the Matrix?
  8. Thread: The 2014 Mitty

    by gnosez
    Replies
    5
    Views
    669

    Thanks for the pictures! Lots of cars and drivers...

    Thanks for the pictures! Lots of cars and drivers I run with up north must have gotten really sick of our weather and made the trip down.
  9. Replies
    10
    Views
    609

    Picture of the bar end would help us help you..

    Picture of the bar end would help us help you..
  10. Replies
    43
    Views
    2,309

    Better fuel pump and if I had to do it all over...

    Better fuel pump and if I had to do it all over again I'd use the Z31 rotors up front instead.
  11. I'll be there. It will be my 12th in 14 yrs....

    I'll be there. It will be my 12th in 14 yrs. Flying in and then crewing up at the Historics the following weekend. Looking forward to it.
  12. Replies
    43
    Views
    2,309

    Mallory Comp ($$$). I think 250/225 or 225/200...

    Mallory Comp ($$$). I think 250/225 or 225/200 would be fine. Keeping the wheels in contact with the road is a good thing.
  13. Replies
    43
    Views
    2,309

    Strut braces and rear flare

    I have the NLA PDK front strut tower brace and a modified SCCA roll bar as a back brace.

    These are older pics before the gnose headlight covers were added and the 3.0 got swapped out for a 3.2L...
  14. Replies
    43
    Views
    2,309

    I'm running 16X9s with 245s at all corners....

    I'm running 16X9s with 245s at all corners. Fronts are 2.5 neg and fit just fine. I rolled the rears out to form a very small flare and 2 deg neg makes them tuck up okay. The car sits under 6 inches...
  15. Replies
    10
    Views
    609

    Powder Coat...

    Powder Coat...
  16. Replies
    43
    Views
    2,309

    We ran the race car with just slotted strut tower...

    We ran the race car with just slotted strut tower tops for several years (2.5 neg front and 2 rear) by grinding down the stock insulator. Two years ago we welded in the TTT fronts but the backs are...
  17. Replies
    8
    Views
    465

    Running mix of 93 and 110 so a gallon costs me...

    Running mix of 93 and 110 so a gallon costs me about $6.23
  18. Replies
    2
    Views
    538

    Aftermarket for sure. I have a complete one piece...

    Aftermarket for sure. I have a complete one piece lower valence with the the corners included.

    Suspect the PO had an "incident" at one time or other and had it replaced.
  19. Replies
    170
    Views
    14,535

    Sticky: Pushed Z out of garage, flushed coolant and added...

    Pushed Z out of garage, flushed coolant and added DI water. Pressurized Accusump to check for leaks. Added 11 qts of oil, yeah that's correct. Turned over engine until oil pressure went up, then...
  20. $183 and out of stock.

    $183 and out of stock.
  21. Most likely stamped. I got what might have been...

    Most likely stamped. I got what might have been the last cast one from Courtesy last year.
  22. Replies
    30
    Views
    1,111

    L24 or L28

    So which engine is in the car now? The L24 making 240hp or the L28 making 285+ with a CR of 13.5? Can either spin the tires? Does going from a stock 150hp to 285 make the car handle any differently?...
  23. Replies
    30
    Views
    1,111

    BSW - as someone who decided early on not to...

    BSW - as someone who decided early on not to install an L28 turbo, an RB, or a LS motor and instead started with a stock L24 and have ended up over the last 14 years with a foolish 3.2L (L28 stroker...
  24. Loose rack? Center of wheels not seating all...

    Loose rack?

    Center of wheels not seating all the way down on hub? I had this issue with a set of aftermarket wheels and it drove me mad until it some how dawned on me that I had to grind down the...
  25. Ditto on rotating the tires front to back and...

    Ditto on rotating the tires front to back and trying a different set of wheels. Really not liking the drilling concept.
Results 26 to 50 of 99
Page 2 of 4 1 2 3 4