Search:

Type: Posts; User: Darrel

Page 4 of 4 1 2 3 4

Search: Search took 0.01 seconds; generated 44095 minute(s) ago.

  1. Replies
    19
    Views
    1,606

    could be over charging.

    could be over charging.
  2. Thread: Where to buy...

    by Darrel
    Replies
    12
    Views
    1,781

    second the hose method. Same exact spot on each...

    second the hose method. Same exact spot on each carb. I double checked mine with a synch tool and there was no difference.
  3. Replies
    29
    Views
    1,127

    I plan to do MS using the patton adapters. I like...

    I plan to do MS using the patton adapters. I like the fact that I can make it look like it still has su carbs. There will just be some extra wires showing. It will be just like having twin throttle...
  4. I did take my cork gasket off and put it in a...

    I did take my cork gasket off and put it in a book to try and keep it straight. 1/2mm off isn't going to hurt anything, just as long as you're within 1mm it's all good. Unless you want to be exact...
  5. I have used my sight glass on 4 screw and 3 screw...

    I have used my sight glass on 4 screw and 3 screw carbs. The 4 screw carbs I had no problem since you can lift the float lid right off. On the 3 screw, I put a longer fuel hose from the rail to the...
  6. Replies
    9
    Views
    954

    They are pretty much enclosed when installed....

    They are pretty much enclosed when installed. Unless the car was used on really dusty roads. Axle grease is fine.
  7. Replies
    29
    Views
    1,127

    He does sell the adapters separately. You can use...

    He does sell the adapters separately. You can use megasquirt with them.
  8. Replies
    29
    Views
    1,127

    Patton Machine makes adapters that use the su...

    Patton Machine makes adapters that use the su carb throttle bodies to put injectors in. You can either get the whole system or just the adapters. A friend of mine just put one of these systems in his...
  9. Replies
    9
    Views
    954

    The bearing sits on top of the hat for the coil...

    The bearing sits on top of the hat for the coil spring. The insulator sits on top of that. It isn't pressed in, not even a friction fit. Usually the bearing falls out on its own.
  10. Replies
    9
    Views
    954

    If they aren't separated you can still use them....

    If they aren't separated you can still use them.

    There is no bearing mated inside. On the front the thrust bearing just sits on top.

    On the rear there is a hard plastic/rubber that just sits...
  11. Replies
    113
    Views
    14,436

    You can see in my pic Marty posted the guts of...

    You can see in my pic Marty posted the guts of the tool. I didn't take a pic of the other end.

    I use the mag wheel lug nuts to do the pulling and to thread on the end with a lock nut to keep it...
  12. static weight on a '73 with spare, tools and full...

    static weight on a '73 with spare, tools and full tank of gas without driver, 2500 #
  13. Replies
    12
    Views
    520

    Kum bya. Glad you found the problem.

    Kum bya. Glad you found the problem.
  14. Replies
    1
    Views
    562

    A friend of mine has done 5 tracks in 14 days....

    A friend of mine has done 5 tracks in 14 days. 1331 miles on those tracks. Hallett, RA, VIR. Not sure the other two tracks. His last was at VIR today. Last run of his day and trip. Will be on his way...
  15. I had a problem like that, only it wasn't dirty...

    I had a problem like that, only it wasn't dirty connections. It was more vibration disconnecting wires. On my way back home from seattle to denver I stopped for fuel in the middle of nevada. After...
  16. Replies
    7
    Views
    1,026

    MSA, pretty reasonable, less than $40...

    MSA, pretty reasonable, less than $40
    Motorsport! Heater Hoses - The Z Store, Nissan-Datsun 240Z-260Z-280Z-280ZX-300ZX(Z31/Z32)-350Z-370Z Parts
  17. Replies
    7
    Views
    1,026

    Use the formed stock hoses, they will come with a...

    Use the formed stock hoses, they will come with a new grommet for the fire wall.
  18. Replies
    7
    Views
    1,026

    I replied last night, but the forum went down or...

    I replied last night, but the forum went down or something.

    Unless you work for cirque de sole, you would be better off taking the dash out to get to the heater hoses inside. You don't have to...
  19. Replies
    66
    Views
    16,466

    Did you try using a bump stop bolted to the RT...

    Did you try using a bump stop bolted to the RT mount along with the stock diff mount? With my nissan drivetrain I have had no issues at all.

    Only one is needed. And they can easily be found at...
  20. Replies
    1
    Views
    552

    Are you coming or going from home? Stick around...

    Are you coming or going from home? Stick around the denver area and visit High Plains Raceway tomorrow (6-22) for the z club track day. Friday night camping is allowed.
  21. all those places are scams, they say they have...

    all those places are scams, they say they have all the info, but it's never current.

    Try facebook if you have it.
  22. Replies
    4
    Views
    486

    Had someone do that driving my 620. Still waiting...

    Had someone do that driving my 620. Still waiting to set something up in my 240z, don't know what it sounds like when it's on the track.
  23. Replies
    8
    Views
    765

    chain wrench around crank pulley.

    chain wrench around crank pulley.
  24. Replies
    6
    Views
    1,316

    hello to 2008.

    hello to 2008.
  25. I had a friend transfer my vhs copy to dvd, so...

    I had a friend transfer my vhs copy to dvd, so it's the same quality as what the vhs tape was. I don't think ZT remade any portion, but I do believe they transferred it to dvd. I couldn't tell you...
Results 76 to 100 of 100
Page 4 of 4 1 2 3 4