Search:

Type: Posts; User: CarolinaTZ

Search: Search took 0.00 seconds.

  1. Thread: Header id?

    by CarolinaTZ
    Replies
    6
    Views
    2,348

    Thanks for sharing guys. Several of the parts I...

    Thanks for sharing guys. Several of the parts I bought from this guy seem to be from the Japan only market.
  2. Thread: Header id?

    by CarolinaTZ
    Replies
    6
    Views
    2,348

    This appears to be a Japanese market...

    This appears to be a Japanese market header...Datsun Spirit uses it on his 240Z and offers it as part of their exhaust system on datsunspirit.com. It is also discussed on hybridZ in the N/A 400hp...
  3. Thread: Header id?

    by CarolinaTZ
    Replies
    6
    Views
    2,348

    I don't have that book but, I've seen the picture...

    I don't have that book but, I've seen the picture in there of the "Cyclone" header...mine's not the same as that one...if that's what you're referring to. Is there another header in there besides...
  4. Thread: Header id?

    by CarolinaTZ
    Replies
    6
    Views
    2,348

    Header id?

    Hi..can anyone tell me what header I have? 5/8" flange, approx 1-3/4 tubes, dual 2" outlet...thanks!
  5. Replies
    22
    Views
    1,404

    So, how did it go? It's been a while so...

    So, how did it go? It's been a while so hopefully you were able to get it resolved. I have several wavies in my roof and I'm hoping the paintless guy will be able to do the trick.
  6. It appears the rust problem isn't all from the...

    It appears the rust problem isn't all from the water that drains from the top. The panels that I've seen, have mostly rusted from underneath. Moisture gets trapped between the top panel and tail...
  7. Mike, not too much information at all! That's...

    Mike, not too much information at all! That's the kind of description I was looking for. I appreciate the time and thought you put into this and this may be the very product I end up using. It and...
  8. Replies
    4
    Views
    943

    Thanks, Carl...I'm going back to pull the diff...

    Thanks, Carl...I'm going back to pull the diff out of the car so I'll be sure to get the hardware. Is there anything else I should get off the car for the swap? This is the same car I got my 5...
  9. Replies
    4
    Views
    943

    OK...thanks

    OK...thanks
  10. Replies
    4
    Views
    943

    Parts for R200 swap...

    On my 72 240Z, I'm installing an R200 diff from an 82 ZX. Will the hardware (mustache bar, etc) needed from a 280Z work from a 77 auto since it has an R180? Thanks!
  11. I'm planning to spray inside my frame rails also....

    I'm planning to spray inside my frame rails also. What type of wand setup are you using? What are you spraying in there? Thanks, Joe
  12. Replies
    4
    Views
    821

    Oh OK. I understood there to be a difference in...

    Oh OK. I understood there to be a difference in length between the r180 and r200 halfies. That makes it easier then. Thanks again.
  13. Replies
    15
    Views
    5,292

    Installed the replacement panel with 3m panel...

    Installed the replacement panel with 3m panel adhesive...worked great and solid as a rock. And water can't get to it at all...serves as it own seem sealer.
  14. Replies
    4
    Views
    821

    Agreed...it's a puzzle trying to figure what was...

    Agreed...it's a puzzle trying to figure what was done and why sometimes. Knowing the rule of thumb that 280z halfshafts are shorter because of the wider r200 diff... I need a set and have sourced...
  15. Replies
    4
    Views
    821

    240 halfshafts

    Does anyone know if the halfshafts from a 77 280z automatic (which is supposed to have an r180 diff) will drop straight in to my 72 240z?

    Thanks
  16. Replies
    13
    Views
    2,952

    I know hap...the distributor. I was by his shop...

    I know hap...the distributor. I was by his shop and held a retro4. Very nice finish and a good lookin' wheel. He also indicated they may make a wider one too...ddidn't say when though.
  17. Replies
    12
    Views
    2,107

    My 72 was treated...I think when it was new. ...

    My 72 was treated...I think when it was new. It's a greasy, wax substance and they put it everywhere...rockers, doors, quarters and above fenderwells. I have zero rust in these areas. And it...
  18. Replies
    15
    Views
    5,292

    Alright!...another motorcycle guy. Never been...

    Alright!...another motorcycle guy. Never been into Canada...just a lot of trips to East Tennessee and NC mountains. Anyway, back to the subject. I'll be bonding the new panel in. I finished...
  19. Replies
    15
    Views
    5,292

    Looks good grantf...does it seem like the seam...

    Looks good grantf...does it seem like the seam sealer will keep the water out from under the panel (above the tail light panel)? That's the area that always rusts and after welding, it doesn't look...
  20. Replies
    15
    Views
    5,292

    240Z hatch repair panel

    I have a '72 and am in the process of replacing some rusted metal. I have read of the possibilty of bonding the under-hatch (above tail lights) repair panel using one of the high-tec body adhesives....
  21. Replies
    11
    Views
    5,176

    Great looking wheels, guys! Do you know how much...

    Great looking wheels, guys! Do you know how much the 15" weigh vs 16" weight?
  22. Replies
    16
    Views
    1,952

    I had a ZZZap from 83 - 87 and wish I had not...

    I had a ZZZap from 83 - 87 and wish I had not sold it. Didn't really like the decals but they grow on you. One of the 77 Nissan ads shows a non-striped yellow Z and called it a ZZZap...so would...
  23. Replies
    0
    Views
    190

    Hello! from CarolinaTZ

    Hi, my name is Joe and I live in SC. I previously owned an orange '73 and a '77 ZZZAP w/stripes and a Turbo Tom's system. I currently own a white '72 w/ another Turbo Tom's built motor.

    It's...
Results 1 to 23 of 23