Search:

Type: Posts; User: pjoe

Page 3 of 4 1 2 3 4

Search: Search took 0.01 seconds; generated 38525 minute(s) ago.

  1. Replies
    17
    Views
    3,256

    The hardest part for me was getting the inner...

    The hardest part for me was getting the inner sleeve out of the outer rear control arms. I heated them until they were purple with oxy/acetylene torch, cut them down the middle with hacksaw, and...
  2. Replies
    288
    Views
    30,200

    Sticky: worked on engine

    Almost ready to put engine in. Need to find a gasket for transmission. The PO took the rear extension off for some reason and gasket is torn. All the gears seem to work fine and engage...at least for...
  3. Thread: 240 door bumper

    by pjoe
    Replies
    5
    Views
    905

    Spray some silcone spray or soap on it. Get one...

    Spray some silcone spray or soap on it. Get one part started with small dull screw driver then push in and turn. Thats how I did it.

    Brian
  4. Replies
    6
    Views
    828

    I'll ask...how? Cant be as bad as my 2 year...

    I'll ask...how? Cant be as bad as my 2 year project getting totaled by my brother a week before completion. But, if you dont want to say I understand...

    Brian
  5. Replies
    22
    Views
    1,551

    latest progress on 240

    Yesterday I got the dash and wiring harness back in. Ive got one small leak from a brake line at the master cylinder I need to fix. I noticed the front clip is bent a little bit but dont think it...
  6. Replies
    9
    Views
    1,015

    Thanks for the opinions. I was trying to avoid...

    Thanks for the opinions. I was trying to avoid having another hard line that was unnecessary routed through engine bay. As long as it wont hurt anything, I think Im gonna dead end it where it is....
  7. Replies
    9
    Views
    1,015

    Thats is what Im talking about. just figured it...

    Thats is what Im talking about. just figured it would be one less thing in engine bay. Dont remember if the k&n's have fitting for the vent hose(triple webers). If so I guess I could do that, less...
  8. Replies
    9
    Views
    1,015

    yep the one thats curved down a little in center...

    yep the one thats curved down a little in center of firewall. Used to go to air cleaner I think but im not planning on hooking it up to triples. But I am planning on leaving it open.
  9. Replies
    9
    Views
    1,015

    will this vent hose be ok like this?

    I think Im gonna just turn the vent hose from rear of car down right at firewall. Maybe I can find some kind of cap that will still let it breath. Anyone see a problem with doing this? I'd rather...
  10. Replies
    5
    Views
    658

    Cool. Think Im going to install what I have and...

    Cool. Think Im going to install what I have and see how it works out. I thought my 73 was sitting pretty damn low. This is the suspension from that car, so it explains alot. If I have problems I...
  11. Replies
    5
    Views
    658

    Thanks Blue. Wonder if Im going to have any...

    Thanks Blue. Wonder if Im going to have any issues running these springs with new kyb gas struts?
  12. Replies
    5
    Views
    658

    stock 240 spring measurements

    Anyone know the height of stock springs off the strut housings. Mine are about 11 inches in back and maybe 12 inches in front. Does this sound to be stock? Here's a crappy cell phone pic of the...
  13. Replies
    2
    Views
    853

    cool. I hope this works out ok. I really dont...

    cool. I hope this works out ok. I really dont want to have my suspension off again for a while. My sway bars are 7/8 inches which I dont think are stock...are they? And the car had the aluminim ball...
  14. Replies
    2
    Views
    853

    are my springs worn out?

    Im geting ready to replace struts on my 240 and wonder if my springs are worn out. Everyone talks about spring compressors but I can easily get my springs off without a compressor. I just hold a...
  15. Replies
    38
    Views
    9,955

    Those wheels look cool as hell. Brian

    Those wheels look cool as hell.

    Brian
  16. If it doesnt work out...I have a couple sets....

    If it doesnt work out...I have a couple sets. Mine would need to be cleaned up and gone through.

    Brian
  17. Replies
    9
    Views
    1,635

    Is the brake waring switch the same between 71...

    Is the brake waring switch the same between 71 and 73? It appears to be the same.
  18. Replies
    9
    Views
    1,635

    Thanks blue. I see it there. Just ordered...

    Thanks blue. I see it there. Just ordered adjustable one from jegs for 40 bucks. Guess I can mount it there or in the front somewhere. Might be easier to get to in the front. Picture helps and I...
  19. Replies
    9
    Views
    1,635

    Thanks. Looked again tonight and couldnt find...

    Thanks. Looked again tonight and couldnt find valve so I guess I'll order the adjustable one from msa.
  20. Replies
    9
    Views
    1,635

    Proportioning valve on 71. (10\70)

    Anyone have a picture of the proportioning valve on a (10\70)71 240? I believe its different than the 73 and mounts in back. If someone has picture of the valve and/or picture of how the hard lines...
  21. Replies
    13
    Views
    2,577

    Simple one for you..nails in wall to hang all...

    Simple one for you..nails in wall to hang all your wrenches on. Beats the hell out of digging through tool box.
  22. gotta love ospho and others alike.

    gotta love ospho and others alike.
  23. Replies
    6
    Views
    1,245

    Gotta make do with what I have. Much easier to...

    Gotta make do with what I have. Much easier to weld sitting versus laying down. Im gonna try wet sanding the wrecked z for practice and then do this one. Hope to start transfering suspension, brake...
  24. Replies
    6
    Views
    1,245

    engine bay painted

    I got the engine bay and interior painted this weekend. I have a couple small spots I have to wet sand but over all I think it turned out pretty good. Now time to start putting some parts back on.
    ...
  25. Replies
    38
    Views
    6,617

    Looks graet. I just got my engine bay and...

    Looks graet. I just got my engine bay and interior painted(also did it myself). Hope it turns out as good as yours when its all put back together.

    Brian
Results 51 to 75 of 99
Page 3 of 4 1 2 3 4