Search:

And Zed Head, your right. I knew what I wanted in my head. Ha. I want to bypass the warmer temperature set... plan B looks like a better idea though!

ZKars. Something so simple yet I never even thought of that. The idea of having a spare set of points for backup did enter my mind! Great idea.

If the two sets are basically the same thing, but...

Hello everyone,

I'm still trying to figure out why I have a lack of power from idle(to 1400rpm or so). After digging into the manual a little further, i've found that my automatic drops the...

My physics mind, and my world knowledge are competing and battling for the right answer.

Corrosion definitely increases resistance… Which combined with the equation completely contradicts why the...

As others have stated. A few horrible connections will increase the resistance in the circuit. The engine probably has nothing to do with it. It is just takes a while for the resistance to build...

I don't see this in the classifieds?


EDIT: Just realized this was 2 years old.

Thanks for the reply guys! I might try and get it off this afternoon. I ended up purchasing a new rad, water pump and some electric fans yesterday so having to remove it is now not needed. I think...

Z dreams, if that's the case I guess i'm going the electric fan route. I don't think I have a chance of removing that bolt without an impact gun. Using the starter bump method i've seen online...

746687466974667

Sorry, 1971 240z. Stock with aftermarket A/C(I think. York unit). The spacer is in there and it still doesn't clear. This pulled looks like ts held on by two bolts. I removed them and gave it a...

Hello,

Trying to install a stock cooling fan to replace the flex lite fan that was in the car when I bought it.

Once I got the stock fan installed I noticed it is rubbing the A/C portion (3rd...

1972 Exhaust Manifold. Picked it up off a local for free, and I decided i'm just going to go the header route. Free for anyone who wants to pay for shipping. Emissions piping is cut/pinched off...

I have the basic sync meter (The one in the ZTherapy video) made by Holley. Is there an advantage to the one you posted. A timing light is on my xmas list to myself. I would have purchased it a...

Numbered 1 through 6 from left to right. This was after running the car for 5-10 minutes with the choke on. They look the same as when I pulled them 2 days ago, but the black sewt is new.


I...

Today the car was running even worse. Although it seemed inconsistent. It was also cooler today, although not much.

The brake felt lousy, so I suspect a vacuum leak is part of the problem....

Yes, Day 1. No issues. The hesitation started the next day.



I will try fiddling with the choke and will report back.

Hello all,

1971 240z automatic. Stock.

If you guys have been following my threads on this vehicle, I purchased it about 6 months ago in the great US of A, and imported it into Canada. I've...

Well there you have it. Page 14 explained my answer. I only saw the reference on page 11.

I'll take a look at mine again. It looks the same, perhaps there is something restricting it's...

The manual states I should have them. It does not state how they are operated.

The turn signal stalk does not move forward or back. I fear to break it. But if that is how the operate, I may try...

1971 240z. Finally was able to register my Z. It hit the road for a while yesterday, and then I realized I don't have high beams. Or I just don't know where the switch is.

Should I be equipped...

I just did all my lines, and the right front was the worst one. I used a copper alloy so it was very easy to bend. Once I got the old one out, I copied the first half of it by matching it to the...

Sounds like a vacuum leak. But I am no expert. I've heard of people using propane to detect leaks, if you spray it near a leak, the isle should technically smooth out. Once the propane is removed,...

I believe Arizona Z Car has Springs that are stock height.
http://www.arizonazcar.com/springs.html

I replaced the Rack bushings, and steering coupler already. Feels pretty good now since the alignment! Still movement in the wheels. Probably time to do the wheel bearding just because.

Well the 240z passed the inspection, and they also gave me a "Nice work" on everything I had done. I'lll pass that on to you guys too :p

After the alignment, the car drives straight, and any...