Search:

To give some validity to your assertion that you're not thread bashing, you should also mention that those are blemished items, discussed here just yesterday and that the good ones that Esprit is...

This issue of bypassing the heater has come up many times. The correct way is to BLOCK/PLUG the heater hose connections at the head and lower rad hose fitting at the front. Do NOT just join these...

This is the stuff I bought.

2 Rolls Factory Electrical Non Adheasive Wiring Harness Friction Tape M | eBay

Decent price and good seller.

The tape is made by Elliot tape.

Michigan Tapes...

Just to clarify why it won't work, the AAR is an air bypass to the throttle blade, which affects (increases) idle speed when the engine is cold, but ALL air going to the engine must pass throught the...

All L24/L26/L28 flywheels bolt to the crank, but not all clutches bolt to all flywheels. 225mm clutches use 6 mount bolts, 240mm use 9 bolts, in a different pattern. Sorry, the clutch pack has to...

The simplest way to essentially defeat all this is to rewire the distributor so that the "advance" point contact goes directly to the "-" side of the coil, and remove the "retard" wire from the...

While these are excellent and well tested methods to diagnose very common ignition problem areas, I would preceed these checks by a simple check (immediately after failure) to see if you have spark...

The shop lightening will have an effect on the preceived color. Get it out in the sun before you start wondering about correct shades. Might have to wait until next spring for sun though....

To expand on Tlorber's comments about using an adhesive, which I think is about the only hope you have of making an invisible repair, there are some pretty agressive and strong bonding agents out...

Help. Weak... Have turkey poisoning... Apparently cranberry sauce and gravy are NOT antidotes... Please save me...

The only way anyone has the right to poke fun at someone elses mistakes, is if they have a degree from the university of doing silly things. As anyone who has worked with me knows, I have a PhD from...

The best solution to the points setting issue is get rid of the points. There are several reluctor based distributors available, from later ZX dizzys that bolt right in to Pertronix aftermarket and...

You're going to feel silly when you pull that rubber protector off the threads...

The two threaded holes in the crossmember were used for an optional weight that was hung off the crossmember to...

Just wanted to let everyone know that I spotted a post on 510Realm this morning (I'm an equal Datsun opportunity guy ;) ) from Dave Patton at Futofab regarding an announcement of more 510 body parts...

I'm not positive, but I'm willing to bet its a 4 x 0.7 mm machine screw. Can't go look at the moment but can confirm tonight.

The part number is 08310-40612 if that helps you find some at the...

My favorite part (always) is when they drive away smiling from ear to ear, or maybe when I listen to the sweet exhaust note fading into the distance, with their foot in it 'cause they can't resist......

Sorry, didn't make my joke/point clear enough. Those who want their car "just like it came from the factory" would not accept rebuilt Z therapy carbs if they had the choice of real, period correct,...

Better running, undoubtly. But they are not "right".....

oh baby... any close up shots of its under belly?

Pretty sure you mean "Chevette" springs. Pretty much the same car, right? ;)

I'm Baaaaaack..


Something came in the mail yesterday. It's a lovely 15x40mm u-joint. I believe we have a staked u-joint replacement option. Way to find a good one CanTechZ!

74387

I've...

I apologise for my careless use of grade information. The head of the stock bolt has a "9" on it. I believe this is equivalent to ISO grade 10.9 as John mentions. Look for this designation on the...

30 mm is the length. 12x1.25 is correct. Grade 9. They are special Nissan bolts with a shoulder that fits the steering knuckle tightly.

Incredible!

The pictures do not do them justice. I can imagine the sparkle of the facets in the sunlight.

Power them up and bask in their radiance for 15 min. Get that last bit of tanning in...

There is a spring washer and cotter pin in that connection. The end of the J hook should be a nice fit through the holes in the U shaped hole too to remove as much chance for motion. Also evaluate...