Search:

Type: Posts; User: Curtis240Z

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    17
    Views
    4,678

    Here are some Bob Sharp catalogs...

    Here are some Bob Sharp catalogs...
  2. Because brake pedal travel on stock pedal...

    Because brake pedal travel on stock pedal assemblies are limited, matching a larger MC displacement to larger calipers or drum to caliper retrofits keeps things close to normal.
  3. Replies
    10
    Views
    6,151

    Individual throttle body (ITB) fuel injection is...

    Individual throttle body (ITB) fuel injection is better than triple carbs, but then again it is more work and more money. Plus you need to be able to make you fuel maps or pay a tuning shop more...
  4. Replies
    6
    Views
    1,146

    The Harada unit is a "plug and play" for the S30....

    The Harada unit is a "plug and play" for the S30. The wiring is factory connections (bullet) and the antenna connection is a push-on. Unfortunately the Harada unit is missing the antenna and the...
  5. Replies
    2
    Views
    772

    I don't know about a window crank with a longer...

    I don't know about a window crank with a longer shaft, but if just the center hub is dragging, make sure the plastic washer is still there.
  6. Replies
    6
    Views
    1,146

    To expand on EScalon points: The old unit is an...

    To expand on EScalon points: The old unit is an aftermarket Harada unit for a S30. The replacement you bought looks like it is for ZX because the trim/grommet size (smaller diameter) and antenna tip...
  7. Replies
    18
    Views
    2,476

    Is your clutch fan frozen so the fan runs all the...

    Is your clutch fan frozen so the fan runs all the time?
  8. The crossmember is not just a single formed...

    The crossmember is not just a single formed "upsidedown U" shape. There is an additional steel plate for either reinforcing/proper spacing. I would replace the crossmember. Just my 2 cents.
  9. Replies
    17
    Views
    1,371

    The torque value is correct. The bushing is...

    The torque value is correct. The bushing is directional (front vs. rear)
  10. Replies
    37
    Views
    3,683

    The rubber clutch stop pad located on the...

    The rubber clutch stop pad located on the firewall bracket is NLA.
  11. Thread: parts

    by Curtis240Z
    Replies
    15
    Views
    1,347

    I agree with nahurry. The aftermarket door seals...

    I agree with nahurry. The aftermarket door seals are too robust and won't relax enough over time. The OEM door seals don't have this problem.
  12. Replies
    75
    Views
    5,450

    Mike, Here is what I did.

    Mike,

    Here is what I did.
  13. Replies
    4
    Views
    768

    regular threads

    regular threads
  14. Replies
    45
    Views
    3,467

    Sent in my comments.

    Sent in my comments.
  15. Replies
    31
    Views
    1,181

    This is a '71 Z. The center console and latch...

    This is a '71 Z. The center console and latch type gas door are '70 & '71 items only. I would venture to guess that the chrome shifter stick is also straight, not doglegged like a '72, but I can't...
  16. Replies
    1
    Views
    633

    You might try http://www.hybridz.org they are...

    You might try http://www.hybridz.org they are into more modified setups. I am running a Megasquirt on a TWM ITB setup (see my Z Photos), so the map would not be much help to you.
  17. Replies
    12
    Views
    7,750

    As previously mentioned, you will need to make...

    As previously mentioned, you will need to make only one side "live" and even then you will lose low end torque over more conventional systems. But if it is the sound and look you are after, then to...
  18. Replies
    26
    Views
    6,672

    The debate on which oil is best will always rage...

    The debate on which oil is best will always rage on. What is more important to realize is the older engines weren't designed to run some of the lighter weight oils on the market today, so would...
  19. Replies
    25
    Views
    2,102

    The coolant blockoff looks okay on the intake...

    The coolant blockoff looks okay on the intake side for a 240Z. Did you check to see what Beandip previously mentioned regarding the metered orifice on the metal return line above the mechanical fuel...
  20. Replies
    6
    Views
    763

    The oiler tube openings are plugged on the...

    The oiler tube openings are plugged on the internally oiled cam towers or in your case the cam manufacturer supplied block off plates and gaskets.
  21. Replies
    4
    Views
    643

    A couple of examples

    I have included two brands of headers that I believe are NLA. They both came with/out air injection fittings. I managed to get one of the last ceramic coated Clifford headers before they stopped...
  22. Replies
    6
    Views
    763

    No competition version of an oiler tube. Cam...

    No competition version of an oiler tube. Cam towers are different for an external lubed cam vs. an internally lubed cam.
  23. Replies
    4
    Views
    1,090

    Yes the hex nut section is toward the rear. Be...

    Yes the hex nut section is toward the rear. Be careful installing it in the crossmember because the tolerance is tight and forcing it in shaves the nylon bushing material (not desireable).
  24. Replies
    6
    Views
    2,997

    Well if the exhause manifold is the wrong shape...

    Well if the exhause manifold is the wrong shape (square vs. round) then cost would probably drive the decision since you are not racing it. So if you can find a good used OEM manifold or a proper...
  25. Replies
    4
    Views
    1,090

    The T/C kit also comes with a boot that covers...

    The T/C kit also comes with a boot that covers and ball and socket (which is greased up) to prevent comtamination. The tension is set with the included sheetmetal gauge. The T/C kit keeps your...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4