Search:

Type: Posts; User: Z train

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    138
    Views
    13,585

    Only one way to put this-Leon,go back to...

    Only one way to put this-Leon,go back to school.You haven't a clue.
  2. Replies
    138
    Views
    13,585

    HP is a product of airflow-not fuel delivery...

    HP is a product of airflow-not fuel delivery method.
  3. Replies
    138
    Views
    13,585

    Assuming the stock system is working AS INTENDED...

    Assuming the stock system is working AS INTENDED all of the above EXCEPT performance.
  4. Actually a set of locomotive horns is more fun.

    Actually a set of locomotive horns is more fun.
  5. Replies
    10
    Views
    1,315

    Ya'll are missing the basics:Oil change & air...

    Ya'll are missing the basics:Oil change & air filter cjange prior.
  6. Replies
    138
    Views
    13,585

    While this is accurate,here in Az. on my wifes 78...

    While this is accurate,here in Az. on my wifes 78 620,all they give a rat's ass about is idle emissions,gas cap & that the AIR pump is on the truck.
  7. Replies
    138
    Views
    13,585

    As the merits of the OE system have been...

    As the merits of the OE system have been documented here,it still can't hold a candle to a modern(MS)system.
  8. Replies
    138
    Views
    13,585

    For the day,it was a really,REALLY good piece.But...

    For the day,it was a really,REALLY good piece.But as mentioned,it doesn't like big sticks.THe newer systems will make more power only because they can adapt to bigger cams,change timing & the...
  9. Replies
    15
    Views
    1,936

    $1000.00

    $1000.00
  10. How does it shift without using the clutch?

    How does it shift without using the clutch?
  11. Replies
    36
    Views
    2,801

    Find TDC and see if the line is at 0 or just a...

    Find TDC and see if the line is at 0 or just a hair before.Really long odds on the balancer being the problem.
  12. Replies
    36
    Views
    2,801

    Bump it in 2 degree increments.Sooner or later...

    Bump it in 2 degree increments.Sooner or later it's not going to like the increase.Then drop it down 2 degrees.Tuning is all trial & error.THere is no magical number that ANYONE can tell you will...
  13. Replies
    36
    Views
    2,801

    Screw California.As far as timing goes, the...

    Screw California.As far as timing goes, the figure is a base line,each motor will like what it's gonna like.Play with it untill it runs the best.
  14. Replies
    6
    Views
    2,489

    Same situation but different:My wifes 620 was...

    Same situation but different:My wifes 620 was built with a header,because i had it,so i figured what the hell?Well,i have the factory manifold going back on as time allows.If you do the header,take...
  15. Replies
    13
    Views
    7,021

    O.K.,back to the basics:THe fuel system from the...

    O.K.,back to the basics:THe fuel system from the check valve to the FPR and the seven injectors is a"pressure vessel"of sorts.Assuming no visable line leaks,the pressure is escaping SOMEWHERE(either...
  16. Replies
    13
    Views
    7,021

    You're losing it with ALL those things...

    You're losing it with ALL those things done?Injectors flowed & tested?
  17. Replies
    13
    Views
    7,021

    I installed a in-line check valve(to replace the...

    I installed a in-line check valve(to replace the one at the fuel pump),had all injectors cleaned & flowed(including the CSI)and my hot start issue went away.If the fuel system(from check valve to reg...
  18. Replies
    16
    Views
    9,310

    No, i meant output shaft.SLIM possibility that it...

    No, i meant output shaft.SLIM possibility that it is the tailshaft bushing(not likely).If i were a betting man, i'd go with the u-joints or further back.
  19. Replies
    16
    Views
    9,310

    It's not the pilot bushing/bearing.It's at or...

    It's not the pilot bushing/bearing.It's at or past the output shaft.
  20. "Elephant snot"(3M trim adhesive)the gasket to...

    "Elephant snot"(3M trim adhesive)the gasket to your cover and then use grease(thin film) between the cover & head.No more issues.
  21. Replies
    15
    Views
    4,915

    Wash the filters at short intervals.

    Wash the filters at short intervals.
  22. I sent mine to be cleaned & flowed for $17.00 a...

    I sent mine to be cleaned & flowed for $17.00 a piece.If those are remans,you have no way to tell if they are any better than yours.
  23. Tire Racks info is wrong.810's came with...

    Tire Racks info is wrong.810's came with 185/70/14s on 6 inch rims.
  24. Agreed.

    Agreed.
  25. Replies
    33
    Views
    6,135

    If all things are correct,a FI car can not...

    If all things are correct,a FI car can not "vapor-lock".
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4